Chibi Aira Shiratori by Chibi Station - Kit Overview
Aira Shiratori from Dandadan as a Chibi Station chibi: masked, mid-leap over a heap of rubble, and wrapped in one magenta sweep of hair that is the largest part in the kit and too big for a Saturn-class plate laid flat.
Aira Shiratori from Dandadan as a Chibi Station chibi: masked, mid-leap over a heap of rubble, and wrapped in one magenta sweep of hair that is the largest part in the kit and too big for a Saturn-class plate laid flat.
This post is written from the studio's files and renders. I have not printed it yet.
At a glance
- Studio: Chibi Station
- Character and source: Aira Shiratori, Dandadan
- Section: Anime
- Versions and sizes: one version, the raw
STLfolder. Assembled, roughly 215 mm tall, 155 mm wide and 125 mm deep (H × W × L), my estimate. Chibi Station includes no dimension sheet, so every size in this post comes from the STL bounding boxes. - Size note: The studio doesn't give an assembled height for this kit. The height here, about 6 to 9 inches, is my estimate from the STL files.
- Parts: 11
- Presupports: none. Raw STLs only, with no presupported files and no slicer project.
- Largest part and plate fit:
Chibi_Station_Aira_Hair.stl, 152.2 × 181.2 × 125.2 mm. It does not fit a Mars-class or a Saturn-class plate flat in any orientation.Chibi_Station_Aira_Head1.stl(94.4 × 104.9 × 99.7 mm) fits Saturn-class only. The other nine parts fit Mars-class. - Ratings (estimated): Print 5/5, Assembly 4/5, Paint 4/5. Skill level: advanced.
- Status: files reviewed, not printed
- Where to get the files: from the studio, Chibi Station.
The model
Aira is caught mid-leap on top of a heap of broken concrete. One boot is planted on a slab. The other knee is drawn up high in front of her. Both arms swing out low to the sides, palms down and fingers loose, as if she is catching her balance. Her body turns a little to her right, and her head tips toward the viewer.
The face is the identifying detail. A grey cloth wrap covers the crown of her head, the left half of her face and her chin, gathered in folds under the jaw. A beige adhesive bandage sits high on the wrapped forehead. Over the wrapped side is a face mask with white straps and a tan pad, perforated like a second bandage, and the strings run across the uncovered side of her face. That side shows one large red eye with a white ring, a black pupil and a white highlight, heavy dark liner, and a crimson stripe above it. Below the eye, the lower face is navy-black, split by a wide grin of long cream teeth edged in red. The grin runs the full width of the jaw, under the mask as well. Magenta bangs fall across her brow, and one lock crosses the uncovered eye.
The costume, item by item. A long open coat in pale blush pink, with red lining at the notched lapels and the inside hem, and two round dusty-rose buttons on the front panel. The coat sleeves end in navy ribbed knit cuffs, and her hands are bare. Under the coat, a pale grey zip-up top with a stitched zip line and two small royal blue tabs on the chest. A navy ribbed band at the waist. A short pleated indigo skirt. Violet thigh-high stockings with a soft sheen. Tan-brown lace-up ankle boots.
The base is urban wreckage. Broken blue-grey concrete slabs are stacked into a low heap on a bed of dark brown dirt and pale pebbles. At the back left, a broken wall stub has rusted rebar rods sticking out of it. Two rusted pipe ends open at the front left, a rusted pipe elbow sits at the front right, and a rusted steel beam leans up at the back right. The hair carries the footprint. From a lavender scrunchie at the back of her head, it rises into a high loop over her, swings out to the right, and sweeps down the left side (as you face her) to lie across the rubble. A second bundle of tapered strands curls up beside her boot. The figure sits inside that loop, and the loop sets both the height and the width of the build.
Versions and sizes
STL- H × W × L: roughly 215 × 155 × 125 mm assembled (my estimate)
- Pieces: 11
- Presupported (format): No (raw STL only)
The height is my estimate from stacking bounding boxes against the full render. The hair is 181.2 mm on its longest side and stands upright, running from the top of the rubble to the top of the build. The width and depth are the hair's other two sides, 152.2 and 125.2 mm, which overhang the base.
There is one version. It suits someone with a large-format resin printer, or a Saturn-class owner willing to tilt or cut the hair. It is a big chibi, closer to a standard display figure in size, so plan shelf room for the hair loop. Painters who like faces, small freehand work and rust weathering will get the most out of it.
About the sizes. Every measurement in this post comes from the sculptor's files or the studio's published size information for the unprinted model. A printed kit can differ slightly: resin shrinks a little as it cures, removing supports and sanding takes off some material, and the assembled height depends on how the parts are fitted. Treat the numbers as a close guide, not an exact guarantee.
What's in the download
Figure
Chibi_Station_Aira_Head1.stl: Head: grey wrap, mask, grin, bangs and, by its size, the upper hair mass- Size mm: 94.4 × 104.9 × 99.7
- Notes: Heaviest part. Saturn-class only. 7,564,448 triangles. I can't tell from the renders where it ends and the hair begins.
Chibi_Station_Aira_Head.stl: Small head piece, about 33 mm across. By size, a face or mask insert for Head1, not a second head- Size mm: 33.3 × 34.2 × 18.9
- Notes: Thin.
Chibi_Station_Aira_Hair.stl: The long sweep of hair: the loop over her head and the strands that land on the base- Size mm: 152.2 × 181.2 × 125.2
- Notes: Largest part. Fits neither Mars- nor Saturn-class flat. Tapered strand tips are fragile
Chibi_Station_Aira_Body.stl: Torso: zip-up top, waistband and skirt- Size mm: 31.1 × 77.8 × 42.4
- Notes: The 77.8 mm side is longer than the torso looks in the renders; some of it likely sits hidden under the coat
Chibi_Station_Aira_L_Arm.stl: Arm with coat sleeve, navy cuff and open hand- Size mm: 27.3 × 21.8 × 32.5
- Notes: Thin fingers
Chibi_Station_Aira_R_Arm.stl: Arm with coat sleeve, navy cuff and open hand- Size mm: 36.0 × 37.9 × 22.9
- Notes: Thin fingers
Chibi_Station_Aira_L_Leg.stl: By its long, straight shape, the standing leg: stocking and boot- Size mm: 23.1 × 65.7 × 23.2
- Notes: Carries the figure on the base
Chibi_Station_Aira_R_Leg.stl: By its compact shape, the raised, bent leg: stocking and boot- Size mm: 31.7 × 43.3 × 32.3
- Notes: Join hidden under the skirt
Cloth
Chibi_Station_Aira_Under_Coat.stl: The long open coat, by size- Size mm: 65.1 × 69.4 × 60.0
- Notes: Thin, cupped shell. I can't tell whether it is the whole coat or only the lower panels.
Base and scene
Chibi_Station_Aira_Base.stl: Rubble base, the larger of two base files- Size mm: 88.8 × 68.9 × 78.4
- Notes: Solid. Thin rebar rods if this half holds the wall stub
Chibi_Station_Aira_Base_002.stl: Rubble base, the second base file- Size mm: 74.0 × 45.9 × 78.1
- Notes: Solid. Shares a roughly 78 mm side with Base. I haven't confirmed how the two fit together.
Nothing in the folder is presupported. It holds 11 STLs and nothing else: no supported files, no .lys or other slicer project. The renders show the figure assembled, so I can't see any pegs or sockets.
A few things are odd. There are two head files, but they are not alternates: Head.stl is 33.3 × 34.2 × 18.9 mm against Head1.stl at 94.4 × 104.9 × 99.7 mm, so the small one reads as an insert. There are two base files, and their matching 78 mm side suggests two halves of one base rather than a choice of bases. Head1.stl alone is 7,564,448 triangles, more than the other ten files combined (6,220,822).
Every file appears to be used once, so one build uses the whole folder: 11 parts. If Head.stl turns out to be an alternate rather than an insert, one build is 10 parts.
Print difficulty
Print: 5/5 (estimated). The hair decides this rating.
Chibi_Station_Aira_Hair.stl is 152.2 × 181.2 × 125.2 mm. It fits neither a Mars-class nor a Saturn-class plate flat in any orientation. Its two shortest sides are 152.2 and 125.2 mm, and the short side of a Saturn-class plate is about 123 mm, so laid flat it overruns by a couple of millimetres. Tilted, the strands may clear, because the mesh is a loop of strands and not a solid block. I have not tried it in Lychee. If it doesn't, it needs a larger printer or a cut.
There are no presupports for any part. Chibi Station ships raw STLs only here, so every part gets supported from scratch. With no supported files to compare, there is no sign of studio hollowing.
The heavy parts are solid. Head1.stl is the heaviest part, solid in a 94.4 × 104.9 × 99.7 mm box, and fits Saturn-class only. Hollow it and add drain holes. The two base files are solid too and need the same. Their flat undersides make large cross-sections, so I would angle them. Head1.stl is also the heaviest mesh in the folder, so expect it to load and slice slowly.
The coat, Under_Coat.stl at 65.1 × 69.4 × 60.0 mm, is a thin cupped shell. Orient it so the inside doesn't face the FEP and form a suction cup.
The thin parts to watch are the tapered hair-strand tips, the rebar rods on the base, and the fingers on both arm files.
The small parts are easy. The arms, the legs and Head.stl all fit Mars-class.
Assembly difficulty
Assembly: 4/5 (estimated). Eleven parts is not many. The difficulty is the weight and where it sits.
Head1.stl and Hair.stl are the two heaviest parts in the kit. They sit on a much lighter body and one standing leg that is 23.1 mm thick at most. The full render shows only one boot touching the rubble. The hair's lower strands lie across the rocks, so the hair is probably a second contact point with the base.
Pinning is the plan, not an option to think about. Pin the standing leg into the base, the head to the body, and the hair to the head. Hollowing Head1.stl helps here too.
Order matters. The hair has to meet the head and the base at the same time. I would join the two base halves first, then fit the legs, body, coat and arms, set the figure on the base, add the head, and fit the hair last so it can be lined up where it lands on the rubble. Dry-fit all of it before any glue.
Visible seams: the shoulders, where the arms meet the smooth pale coat; the collar, where Head1.stl meets the body; and the line between the two base halves, which the rubble texture should help hide. The leg joins sit under the skirt and coat. The smallest piece is Head.stl.
Paint difficulty
Paint: 4/5 (estimated). This is a lot of materials on a small figure, plus freehand work on the face.
I count about fifteen materials: hair, scrunchie, grey cloth wrap, two bandages, mask straps, skin, the navy-black lower face, teeth and gums, the eye, coat with its red lining and buttons, knit cuffs and waistband, zip top with blue tabs, skirt, stockings, boots, and then concrete, dirt and rusted metal on the base.
The face is the hard part. The uncovered eye needs a red iris, a white ring, a highlight, dark liner and the crimson stripe, all on a small area. The grin is a row of individual cream teeth with red edging across a navy-black field. Both bandages have perforation dots. The hair is a large mass of thick strands that needs clean, even shading in the recesses. The stockings have a sheen. The base needs rust weathering on the rebar, pipes and beam.
What keeps it from a 5: there is no glow or translucent effect, and the skin is limited to the hands, the uncovered half of the face and a small band above the stockings, in a cartoon style.
Paint reference. The studio's colors, material by material. Hair: saturated magenta, deepening to berry-violet in the recesses between strands, with lighter pink on the top edges. Scrunchie: lavender. Head wrap: cool mid-grey cloth, lighter on the raised folds. Bandages: tan with darker perforation dots. Mask straps: off-white. Skin: pale peach. Eye: red iris, white ring, black pupil, white highlight, black liner and lashes, a crimson stripe above. Lower face: navy-black. Teeth: cream, edged in red. Coat: pale blush pink with red lining, dusty-rose buttons. Cuffs and waistband: navy knit. Zip top: pale grey-white with a stitched zip line, royal blue tabs. Skirt: deep indigo with a slight sheen. Stockings: violet with glossy highlights. Boots: warm tan-brown leather with darker laces. Base: blue-grey concrete with lighter chipped edges, dark brown dirt with pale pebbles, and orange-brown rust with darker pitting on the rebar, pipes and beam.
Gallery
Two renders, in the studio's order. The "STL" label, the AIRA SHIRATORI lettering, the round Chibi Station badge and the faded image of the character in the backdrop are render graphics, not part of the model. Both files have "test" in their names; they look like finished color renders.


Links
- Studio Patreon: Chibi Station on Patreon
- Studio store: Chibi Station on Gumroad · Chibi Aira Shiratori on Gumroad
- Cults3D: Chibi Station on Cults3D
- Thangs: Chibi Station on Thangs