Satoru Gojo Bust by Tanuki Figures - Kit Overview
Satoru Gojo from Jujutsu Kaisen as a 147 mm, 1/6 bust by Tanuki Figures: blindfolded, smiling, his right hand raised with two fingers crossed. The whole uniform is sculpted in a coarse weave, and the kit carries a second head and hair set plus a pair of glasses.
Satoru Gojo from Jujutsu Kaisen, as a 1/6 bust by Tanuki Figures. He's blindfolded and smiling, with his right hand raised beside his head and two fingers crossed.
What's notable: the surface work. The whole uniform, tall collar included, is sculpted in a coarse woven texture, the blindfold in a fine mesh, and his hair bursts up over the band in dozens of flame-shaped spikes. The kit also has V1 and V2 head and hair files and a pair of glasses. The renders show only the blindfolded build.
This post is written from the studio's files and renders. I have not printed it yet.
At a glance
- Studio: Tanuki Figures
- Character and source: Satoru Gojo, Jujutsu Kaisen (anime)
- Section: Anime
- Versions and sizes: One bust, 147 mm tall × 103 mm wide × 90 mm deep (the studio's numbers), at the studio's default scale of 1/6. It comes as a raw file set and a presupported file set.
- Parts per version: 8 files in each set: torso, hand, base, two heads, two hair pieces, and glasses. One build uses 5: base, torso, hand, one head and one hair piece. Add the glasses and it's 6.
- Presupports: Yes. All eight files in
Supported/STL/are presupported STLs. Seven carry the_SUPsuffix and the torso doesn't (more in What's in the download). The guide also lists editable Lychee.LYSprojects. - Largest part and plate fit: Raw:
Torso_Bust.stl, 90.8 × 81.2 × 89.6 mm. Presupported:Torso_Bust.stlinSupported/STL/, 125.8 × 76.4 × 82.3 mm. Every part in both sets fits Mars-class and Saturn-class plates. - Ratings (estimated): Print 2/5 presupported, 3/5 raw. Assembly 2/5. Paint 3/5. Skill level: intermediate (paint sets it, and so does printing from the raw files).
- Status: files reviewed, not printed
- Where to get the files: Tanuki Figures on Patreon and Tanuki Figures on Gumroad
The model
Gojo is cut off at mid-chest, and the bust ends at his left upper arm. His right arm is bent up at the elbow and the hand is raised to the height of his face, a little out from his head, palm toward the viewer. The index and middle fingers are crossed and point up. The ring and little fingers curl into the palm, and the thumb stands out to the side. It's the crossed-finger sign he uses for his Domain Expansion. His head is turned a little toward the hand, and he's smiling. The identifying details are the blindfold, the white hair standing straight up above it, the tall-collared uniform and the hand sign.
The renders are unpainted gray, so the colors are in the paint reference below. The costume, item by item:
- Jacket: a long-sleeved uniform jacket, loose and boxy through the shoulders, covered all over in a coarse basket-weave texture. A raised placket band runs from the base of the collar straight down the front to the hem. At the bottom the hem is cut to a point at the front, where the bust meets the post.
- Collar: a very tall standing collar that rises to his chin and the bottoms of his ears. It's sculpted as thick fabric folding over on itself in two or three soft rolls. A seam runs down its front, and a short tab sits at its base where the placket starts. His neck shows inside it.
- Right sleeve: wide, and slid back toward the elbow so the forearm is bare. The cuff has a rolled edge. Folds bunch at the inside of the elbow in the side and rear views.
- Left side: the bust stops at his left upper arm with a straight cut, so the left sleeve is only a stub at the shoulder.
- Blindfold: a wide band wrapped all the way around his head over the eyes and brow. It's sculpted as a fine mesh of tiny holes, like a perforated or knit fabric. At the front its lower edge curves down over each eye and up over the bridge of his nose, like a sleep mask. At the back it lies flat, with a slight overlap on one side and no knot.
- Hair: above the band, it rises in a crown of tapered, flame-shaped spikes, each grooved along its length, pointing up and fanning out to the sides and back. Below the band at the back it's cropped short, sculpted in fine strands down to the nape. Short sideburns in fine strands sit in front of both ears.
With the eyes covered, the face is all in the lower half. He has a narrow straight nose, smooth cheeks and a pointed chin. The mouth is a wide, easy smile with the corners turned up and the lips just parted. Both ears are sculpted in detail, folds and all. The skin is smooth and anime-styled, which sets it apart from the textured fabric and the mesh band. The hand has sculpted nails and knuckle creases, and the rear views show the tendons on its back.
The base is a tapered post with a raised rib up its back face, rising from a round plinth. The plinth has a recessed top disc inside a raised rim, a stepped lip at the bottom, and angular buttress blocks with pointed tops set around the rim. There's no scenery on it. The hair and the raised hand carry the outline at the top: the spikes fan out wider than his head, and the hand rises clear of his body on one side, its fingertips at about the level of the blindfold. The shoulders and the sleeve set the width; the torso file is 90.8 mm across of the bust's 103 mm. The torso's 89.6 mm depth sets the bust's 90 mm, and the plinth, 82.8 × 82.6 mm in its file, sits under the middle.
Versions and sizes
- Bust, raw files (
No_Supported/)- H × W × L: 147 × 103 × 90 mm
- Pieces: 8 files, 5 per build (6 with glasses)
- Presupported (format): No
- Bust, presupported (
Supported/STL/)- H × W × L: 147 × 103 × 90 mm
- Pieces: 8 files, 5 per build (6 with glasses)
- Presupported (format): Yes, STL (
_SUP.stl, except the torso); the guide also lists.LYSprojects
The sizes come from the kit's Printing & Scale Guide: Height 147 mm, Width 103 mm, Depth 90 mm. The guide gives 1/6 as the default scale.
Switch-out options. The studio's guide calls V2 parts switch-out alternates. These are the choices:
- Slot: Head
- V1 file:
Head_V1.stl - V2 file:
Head_V2.stl - Raw size (V1 / V2): 43.5 × 72.6 × 39.4 / 32.9 × 53.3 × 35.7 mm
- V1 file:
- Slot: Hair
- V1 file:
Hair_Head_V1.stl - V2 file:
Hair_Head_V2.stl - Raw size (V1 / V2): 29.6 × 26.4 × 16.9 / 42.6 × 38.3 × 49.2 mm
- V1 file:
- Slot: Glasses (optional)
- V1 file:
Glasses.stl - V2 file: none
- Raw size (V1 / V2): 25.6 × 12.1 × 14.8 mm
- V1 file:
These pairs aren't small variations. Head_V1.stl is 72.6 mm on its long side against 53.3 mm for Head_V2.stl, and Hair_Head_V2.stl (42.6 × 38.3 × 49.2 mm) is far bigger than Hair_Head_V1.stl (29.6 × 26.4 × 16.9 mm). That fits one head carrying most of its hair sculpted on with a small extra piece, and the other taking a full separate hair piece. So I've paired V1 with V1 and V2 with V2 for the builds below.
The renders show one build: the blindfold with the hair spiking up over it, and no glasses. He doesn't wear the glasses over the blindfold here, so they likely go with the other head, which may be his unmasked look. No render shows that head, the second hair piece or the glasses. I haven't confirmed which head and hair files make the blindfolded build, whether V1 pairs with V1 and V2 with V2, or which build the glasses go with.
The presupported set suits anyone printing at the studio's size who wants to load and go. The studio has already hollowed the torso, both heads, the base and the larger hair piece, and set the supports.
The raw set suits anyone who wants a different scale, their own hollowing, or their own supports. The studio says never to re-scale the presupported files; scale the raw ones instead. At 1/4 (150%) the bust comes to 220.5 × 154.5 × 135 mm. The raw torso grows to 136.2 × 121.8 × 134.4 mm and the base to 124.2 × 76.4 × 123.9 mm, so check both against your plate.
Tanuki also has a full-figure Satoru Gojo kit, which has its own post.
About the sizes. Every measurement in this post comes from the sculptor's files or the studio's published size information for the unprinted model. A printed kit can differ slightly: resin shrinks a little as it cures, removing supports and sanding takes off some material, and the assembled height depends on how the parts are fitted. Treat the numbers as a close guide, not an exact guarantee.
What's in the download
The kit's guide lists no-support and presupported STL files, editable .LYS files, render images, and an assembly guide video, though no video file is in this kit folder. Four renders are in Images/.
No_Supported (raw) — 8 files
Figure
Torso_Bust.stl: Torso: woven jacket, tall rolled collar, stub of the left sleeve, wide right sleeve- Size (mm): 90.8 × 81.2 × 89.6
- Notes: Largest and heaviest part. Solid as supplied; hollow it if you print raw.
Hand.stl: Right hand in the crossed-finger sign, with the bare forearm- Size (mm): 21.6 × 54.5 × 20.7
- Notes: At 54.5 mm long it likely runs down into the sleeve. Raised fingers are thin.
Base and scene
Base_Bust.stl: Round plinth with buttress blocks, and the tapered post- Size (mm): 82.8 × 50.9 × 82.6
- Notes: Solid. The 50.9 mm height takes in the post as well as the plinth.
Alternates
Head_V1.stl: Head, V1; the larger of the two- Size (mm): 43.5 × 72.6 × 39.4
- Notes: Pick one head.
Head_V2.stl: Head, V2- Size (mm): 32.9 × 53.3 × 35.7
- Notes: Pick one head.
Hair_Head_V1.stl: Hair piece, V1; small, and where it sits isn't shown- Size (mm): 29.6 × 26.4 × 16.9
- Notes: Pick one hair piece. Thin tips likely.
Hair_Head_V2.stl: Hair piece, V2; wider than either head, so likely a full hair cap- Size (mm): 42.6 × 38.3 × 49.2
- Notes: Pick one hair piece.
Accessories
Glasses.stl: Glasses, not shown in the renders- Size (mm): 25.6 × 12.1 × 14.8
- Notes: Optional. Wire-thin and fragile.
None of these are presupported; they're the solid source meshes. There's no _MERGED file, no _EFFECT part and no fix note in this kit.
Whole folder. 8 files. One build is the three shared parts (torso, hand and base) plus the V1 head and hair or the V2 head and hair: 5 pieces, or 6 with the glasses.
Supported/STL (presupported) — 8 files
Figure
Torso_Bust.stl: Torso, presupported- Size (mm): 125.8 × 76.4 × 82.3
- Notes: The studio hollowed it. No
_SUPsuffix. Largest part on the plate.
Hand_SUP.stl: Hand, presupported- Size (mm): 38.5 × 32.3 × 61.1
- Notes: Solid, with supports added.
Base and scene
Base_Bust_SUP.stl: Base, presupported- Size (mm): 91.2 × 91.2 × 68.1
- Notes: Hollowed. Tilted off the plate.
Alternates
Head_V1_SUP.stl: Head V1, presupported- Size (mm): 49.2 × 56.2 × 76.1
- Notes: Hollowed.
Head_V2_SUP.stl: Head V2, presupported- Size (mm): 42.2 × 49.2 × 63.2
- Notes: Hollowed.
Hair_Head_V1_SUP.stl: Hair V1, presupported- Size (mm): 37.7 × 37.7 × 27.7
- Notes: Mostly supports.
Hair_Head_V2_SUP.stl: Hair V2, presupported- Size (mm): 53.6 × 66.0 × 47.2
- Notes: Hollowed.
Accessories
Glasses_SUP.stl: Glasses, presupported- Size (mm): 35.2 × 21.2 × 16.7
- Notes: Mostly supports.
All eight parts are presupported. One thing is odd in this folder. The presupported torso is the only file without the _SUP suffix: it's Torso_Bust.stl, the same name as the raw torso. The numbers show it's the presupported one: it's 125.8 mm long as it stands on the plate, and about 1.47 million triangles against the raw file's 1.09 million. Keep the two folders apart so you don't load the raw torso by mistake.
The guide's editable .LYS Lychee projects sit in Supported/LYS/. They aren't in my STL report, so I haven't listed them.
Whole folder. 8 files, split the same way as the raw set: 5 pieces per build, or 6 with the glasses.
Print difficulty
2/5 presupported, 3/5 raw (estimated).
Plate fit is easy. Every file in both sets fits a Mars-class plate. The biggest is the presupported torso, stood up at 125.8 × 76.4 × 82.3 mm. The presupported base is 91.2 × 91.2 × 68.1 mm, tilted off the plate rather than laid flat.
The studio hollowed the torso, the base, both heads and Hair_Head_V2. The hand and the small hair piece appear to be solid.
The thin parts are the hair spikes, the crossed fingers and the glasses. The spikes taper to points all around the crown, and there are dozens of them. The raised fingers stand free of the palm. The glasses are a wire-thin 25.6 mm frame, and their presupported file is mostly supports. Cut those supports with flush cutters rather than snapping them. Hair_Head_V1_SUP is mostly supports too.
All the files read cleanly in the mesh check, with no degenerate triangles.
From the raw files it's a 3. The torso, the base and Head_V1 are the biggest solid parts, and they need hollowing and drain holes. The tall collar wraps around the neck opening, so look at that area when you place drains. The spikes and fingers need careful supports of your own.
Assembly difficulty
2/5 (estimated).
Five parts per build: base, torso, hand, head and hair piece. Six with the glasses. No part is large or heavy enough to need pinning.
The joins look easy to hide. The head seats in the torso at the neck, and the collar stands up to his chin, so that seam should sit inside it. The hand file includes the forearm, and the wide sleeve has slid back from it, so that join should sit inside the cuff. The torso sits on top of the base post, where the join is under the bust. The hair piece should disappear among the strands.
One thing to look at: in Gojo_Bust_TanukiFigures_04.png, a thin straight line runs down the side of his neck from below his right ear to the collar. It may be a part line or just a sculpted line. The renders don't show where the splits fall or whether the joins are keyed.
The hand is held up and out from his body, but it's a small part. Glue should hold it. A pin would make it sturdier for handling, but it isn't required.
The glasses are the fiddly part. They're a wire-thin 25.6 mm frame that has to sit level on the nose with only small contact points to glue.
Paint the head and neck before the head goes in. The collar wraps close around the neck, and that skin will be hard to reach afterward.
Paint difficulty
3/5 (estimated).
The skin is on part of the model, not most of it: the lower half of the face, the ears, the neck inside the collar, and the right hand and forearm. With the blindfold on, there are no eyes to paint on this head. The skin is smooth and anime-styled, so it wants clean blending rather than texture.
I count five materials: skin, white hair, the blindfold, the uniform and the base. The glasses make six. The two sculpted textures do a lot of the work. The coarse weave on the uniform and the fine mesh on the blindfold both take a wash and a drybrushed highlight well, and they'll read even on a dark color.
The white hair is the hard part. Shading white across dozens of spikes, without it going gray or dirty, takes restraint in the shadows.
There's no freehand pattern and no glow or translucent part. If the other head is an unmasked face, painting his eyes would push it toward a 4. No render shows that head.
Paint reference. All four renders are gray sculpt renders, and the bust is unpainted in them, so there's no studio color scheme to copy. For Gojo's usual look in general terms: white hair, a black blindfold, a dark navy high-collar uniform, blue eyes if you build an unmasked head, and round dark glasses. The skin and the base aren't shown in color anywhere in the kit, so those are your call.
Gallery




Links
- Want it printed? Get the unpainted kit in the store.
- Studio Patreon: Tanuki Figures on Patreon
- Studio store: Tanuki Figures on Gumroad · Satoru Gojo Bust on Gumroad