Chibi Doctor Doom by Chibi Station - Kit Overview

Chibi Station's Doctor Doom plants one armored boot on a riveted machine block, glaring out of a deep green hood. The kit comes split or in one piece, with a swap-in open hand that holds a glowing cube.

Share
Chibi Doctor Doom standing on a round bronze and concrete base, fists clenched, left boot on a ribbed machine block.

Doctor Doom from Marvel Comics as a Chibi Station chibi: riveted iron mask, deep green hood and cape, one boot up on a machine block. What stands out is the folder. It has a split kit with a swap-in open hand and a glowing cube, plus two one-piece versions of the whole statue, and most of the files load at about 1.25 m tall, so scaling is the first job.

This post is written from the studio's files and renders. I have not printed it yet.

Left and right below are Doom's own, not the viewer's.

At a glance

  • Studio: Chibi Station
  • Character and source: Doctor Doom, Marvel Comics
  • Section: Fan art
  • Versions and sizes (H × W × L):
    • Split kit, fist build: roughly 1,248 × 747 × 714 mm as the files load (my estimate)
    • Split kit, cube build: roughly the same (my estimate)
    • One-piece statue, FullStatue: 1,248.4 × 747.3 × 714.1 mm
    • One-piece statue, FullStatue_Cube: 119.3 × 71.4 × 68.3 mm
  • Where sizes come from: Chibi Station ships no dimension sheet, so every size here is an STL bounding box. The files stand Y-up, so H is the report's y. The ruler in render 10 puts the standing statue at about 15 cm. The files don't settle the intended print size: the split parts and FullStatue load about 1,248 mm tall, and FullStatue_Cube loads at 119.3 mm.
  • Parts per version: fist build 9; cube build 10; each one-piece statue 1.
  • Presupports: none. Chibi Station ships this kit as raw STLs only: no presupported files, no slicer projects.
  • Largest part and plate fit: split kit, base at 304.7 × 711.9 × 711.2 mm, fits neither a Mars-class nor a Saturn-class plate as loaded. FullStatue fits neither. FullStatue_Cube fits both.
  • Ratings (estimated): split kit Print 4/5, Assembly 3/5, Paint 3/5 (advanced). One-piece statue Print 3/5, Assembly 1/5, Paint 3/5 (intermediate).
  • Status: files reviewed, not printed
  • Where to get the files: Chibi Station's Patreon and Gumroad store, linked at the bottom.

The model

Doom stands with his right boot on the base's lower step and his left boot up on a ribbed machine block, knee raised, as if he's about to step up. His right arm hangs a little out from his side with a loose fist at hip height. His left arm is bent, fist raised in front of his chest. In the cube build (render 03) that fist becomes an open gauntlet, palm up, holding a glowing blue cube tilted onto one corner. The hooded head is about a third of the statue's height, base included, and wider than his shoulders.

The mask carries the character. It has a rounded brow cap with a curved seam and a row of rivets, heavy brow plates angled down into a scowl, raised frames around the eyes, a straight nose ridge, riveted cheek plates, dark recessed vents on each cheek, a mouth grille with one horizontal bar, and a square chin plate. Inside the eye frames are cartoon eyes: cream whites, orange irises with a darker rim, black pupils, white catchlights. The glare comes from the brow plates pressing down on those eyes.

Costume, item by item. The hood is a deep green with soft, heavy folds that frame the mask; the inside is near black, and at the back of the crown a soft tip folds over (renders 05 and 06). At the collar, two round gold clasps are joined by a twisted gold cord. Under them is a sleeveless green tunic, gathered at the waist and falling to mid-thigh, with the hem parted over the raised knee. A wide brown leather belt closes with a rectangular gold buckle: a scrolled frame and a single prong. The green cape hangs from his shoulders, under the hood, to about mid-shin; it flares wide on his right and falls in deep vertical folds at the back, with a gathered fold just under the hood. The armor is steel gray throughout: rounded, layered pauldrons; a stack of thin rings around his right upper arm above the elbow; rounded elbow cops; gauntlets with segmented finger plates and flared cuffs; domed knee cops with a rivet at the side; greaves with a riveted band; and sabatons with layered toe plates.

The base is a low round disc with a sloped edge in dark bronze-brown metal, brushed and scratched. On it sits a stepped plinth: gray concrete-textured blocks and buttresses, two lighter stone-gray panels at the front over a riveted strip, and a dark riveted drum on the right. The machine block under his left boot is a cylinder of stacked rings with a boxy side housing and a round fitting; its top is flat and round (render 09). Around the back are pipes with elbow bends, a small box with three slots, and riveted square plates (renders 05 and 06). In silhouette, the hood is the big mass at the top, the cape widens down his right side, and the base disc is the widest thing at the bottom. The raised fist, or the cube, is the only thing that breaks the outline, and the raised knee gives the pose its step.

Versions and sizes

  • Split kit, fist build
    • H × W × L (mm): roughly 1,248 × 747 × 714 as loaded (my estimate)
    • Pieces: 9
    • Presupported (format): No, raw STL only
  • Split kit, cube build
    • H × W × L (mm): roughly 1,248 × 747 × 714 as loaded (my estimate)
    • Pieces: 10
    • Presupported (format): No, raw STL only
  • One-piece statue, FullStatue
    • H × W × L (mm): 1,248.4 × 747.3 × 714.1
    • Pieces: 1
    • Presupported (format): No, raw STL only
  • One-piece statue, FullStatue_Cube
    • H × W × L (mm): 119.3 × 71.4 × 68.3
    • Pieces: 1
    • Presupported (format): No, raw STL only

The split-kit height is my estimate. The split parts are at the same scale as FullStatue: the base is 711.9 mm across and FullStatue is 714.1 mm deep, and the hood part alone, head_P1, is 529.4 mm tall. So the assembled kit should stand about as tall as FullStatue.

Who each one suits:

  • Split kit, fist build: painters who want the hood, face, cape and armor apart while they paint. This is the fists-clenched pose in most of the renders.
  • Split kit, cube build: the same, with the open hand and the glowing cube. It's the one to choose if you want to print the cube in translucent resin.
  • FullStatue: a one-piece print for anyone who would rather paint it assembled. Scale it down first.
  • FullStatue_Cube: the quickest route. It's the only file in the folder at a printable size as supplied.

About the sizes. Every measurement in this post comes from the sculptor's files or the studio's published size information for the unprinted model. A printed kit can differ slightly: resin shrinks a little as it cures, removing supports and sanding takes off some material, and the assembled height depends on how the parts are fitted. Treat the numbers as a close guide, not an exact guarantee.

What's in the download

One folder, STL/, with 13 files. It holds the split kit, two hand options, a cube, and two one-piece statues. Sizes are H × W × L in mm, from my STL report.

Split kit

Figure

  • ChibiStation_DR.Doom_head_P1.stl: Head and hood, by size
    • Size mm (H × W × L): 529.4 × 469.0 × 490.1
    • Notes: Heaviest figure part; the hood is deep around the face opening. I matched head_P1 to the hood and head_P2 to the masked face by size against render 02.
  • ChibiStation_DR.Doom_head_P2.stl: Masked face, by size
    • Size mm (H × W × L): 343.1 × 313.3 × 269.9
    • Notes: Close to the mask's size in render 02; seats inside the hood
  • ChibiStation_DR.Doom_torso.stl: Chest
    • Size mm (H × W × L): 200.8 × 276.8 × 259.0
  • ChibiStation_DR.Doom_leg.stl: Both legs, probably with the tunic
    • Size mm (H × W × L): 584.6 × 397.4 × 299.8
    • Notes: Taller than the legs look in the renders. I can't tell from the files how leg and torso divide the body.
  • ChibiStation_DR.Doom_left-hand.stl: The longer arm: matches the hanging right arm with its fist
    • Size mm (H × W × L): 351.9 × 201.8 × 210.1
    • Notes: Named for the viewer's side, it seems: left-hand matches the hanging arm, Doom's right in the renders, and right-hand matches the bent arm. I matched them by size and haven't confirmed it.
  • ChibiStation_DR.Doom_right-hand.stl: The shorter, bent arm that takes the swap hand
    • Size mm (H × W × L): 247.1 × 221.1 × 172.8

Cloth

  • ChibiStation_DR.Doom_cover.stl: Cape
    • Size mm (H × W × L): 554.6 × 631.7 × 386.9
    • Notes: Thin draped shell. Cupped inside

Base and scene

  • ChibiStation_DR.Doom_base.stl: Round base with plinth, machine block and pipes
    • Size mm (H × W × L): 304.7 × 711.9 × 711.2
    • Notes: Heaviest file in the kit. Its height matches the top of the machine block in render 02, so the block is part of it

Alternates (pick one)

  • ChibiStation_DR.Doom_hand2.stl: Fist for the bent arm (fist build)
    • Size mm (H × W × L): 111.7 × 125.9 × 139.5
    • Notes: I matched hand2 to the fist and Hand1 to the open hand for the cube by size against renders 02 and 03.
  • ChibiStation_DR.Doom_Hand1.stl: Open hand, palm up (cube build)
    • Size mm (H × W × L): 119.3 × 164.0 × 164.0
    • Notes: Spread fingers; thin

Accessories

  • ChibiStation_DR.Doom_Hand1_Cube.stl: The cube for the open hand
    • Size mm (H × W × L): 95.9 × 96.4 × 96.4
    • Notes: Near-equal on all three axes, which fits a cube standing on one corner as in render 03. Small contact point; optional

Nothing in the split kit is presupported. One thing in the folder is odd. The two files named left-hand and right-hand are whole arms, not hands; the actual swap hands are Hand1 and hand2. I can't see pegs or sockets in the renders.

One-piece statues

Alternates (pick one)

  • ChibiStation_DR.Doom_FullStatue.stl: Whole statue in one piece, base included
    • Size mm (H × W × L): 1,248.4 × 747.3 × 714.1
    • Notes: Same scale as the split parts. Fits neither plate class as loaded
  • ChibiStation_DR.Doom_FullStatue_Cube.stl: Whole statue in one piece; the name says it holds the cube
    • Size mm (H × W × L): 119.3 × 71.4 × 68.3
    • Notes: Same shape as FullStatue at 1/10.46 the size on every axis (1,248.4 ÷ 119.3). Fits Mars- and Saturn-class as supplied. Going by the name, this is the version that holds the cube; I haven't confirmed it.

Neither one-piece file is presupported. One build is one of these files.

Split kit: 4/5 (estimated).

  • Scale first. As the files load, the split parts are at a 1.25 m scale. Ten of the 13 files fit neither a Mars-class nor a Saturn-class plate in any orientation, per my report; the base alone is 304.7 × 711.9 × 711.2 mm. Scale every split part by the same factor. At about 15 cm (lengths × 0.120), the base comes out about 37 × 86 × 85 mm and the cape about 67 × 76 × 46 mm.
  • Cupped parts. The cape (cover) is a thin draped shell in a 554.6 × 631.7 × 386.9 mm box. Its inside face is a broad cup, so it wants an orientation where the hollow side doesn't face the plate. head_P1, the hood by its size, is deep around the face opening and is the second cup. These two put the kit at a 4.
  • Heavy solids. base and head_P1 are the two heaviest parts. I'd hollow both and add drain holes.
  • Thin bits. The open hand's spread fingers (Hand1), the cape's hem, the cube balanced on one corner, and the twisted cord between the collar clasps.
  • No presupports. Chibi Station ships this kit raw only, so you support everything yourself.

One-piece statue: 3/5 (estimated).

FullStatue_Cube is the only file in the folder that drops onto a plate as supplied: 119.3 × 71.4 × 68.3 mm, which fits Mars- and Saturn-class per the report. It's one solid piece, so hollow it and give it drain holes. The space between the cape and the legs is an open pocket; keep it from facing the plate. FullStatue is the same shape, 10.46 times bigger on every axis, so scale it down and the same applies. With the cape and hood joined to the body, there are no loose cupped shells, which is why it rates a step lower than the split kit.

Assembly difficulty

Split kit: 3/5 (estimated).

Nine parts for the fist build, ten for the cube build. Most joins look like they land on natural breaks in the costume: the arms at the pauldrons, the swap hand at the gauntlet cuff, the face inside the hood. The cape is a large hanging piece that wraps the back and tucks under the hood at the shoulders, so it goes on before the head.

I'd pin the head to the body and pin at least one boot to the base; the right boot stands on the lower step and the left on the machine block. The cube rests on the open palm by one corner, a small contact point. Glue it, and pin it if there's room.

One-piece statue: 1/5 (estimated).

One piece. Clean off the supports and it's assembled.

Paint difficulty

All versions: 3/5 (estimated).

There's no skin anywhere; the face is a mask. The work is in the materials: green cloth, steel armor, gold fittings, brown leather, the eyes, and the base's bronze metal, concrete and stone. The steel is the main job. The pauldrons, knee cops, elbow cops and the mask are big smooth domes that have to read as metal, through metallic paint or painted highlights. The mask and the base carry dozens of raised rivets, which reward a wash and a clean highlight on each one.

The eyes are small freehand work. At about 15 cm, each eye is roughly 5 mm across by my estimate from render 02. The cloth is large and soft, which is friendly for basecoat, shade and highlight. The base adds concrete texture, pipes and riveted plates. The cube build adds a small glow; printing the cube in translucent blue resin skips painting it. Because it's one small part, I'm not raising the rating for it.

Paint reference. From the colored renders: hood, cape and tunic in a mid green with a soft sage highlight on raised folds and deep green-black in the hollows. Mask and armor in a cool steel gray, bright on the domes of the pauldrons and knee cops; the mask is a touch darker and flatter than the armor, with a faint pink-lilac reflection on the nose ridge. Clasps, cord and buckle in a warm polished gold. Belt in mid brown leather with a reddish cast. Eyes with cream whites, orange irises with a darker rim, black pupils and white catchlights. Hood interior near black. Base disc in dark bronze-brown brushed metal with scratches and a warm copper sheen. Plinth blocks in a mottled concrete gray, front panels in a lighter stone gray, drum and machine block in dark bronze with black grooves, pipes in dark bronze. Cube in a translucent bright blue with a pale blue-white symbol glowing inside.

The round Chibistation logo badge, the "3D PRINTABLE" and "DR. DOOM" lettering, "EXCLUSIVE" with the colored dots under it, the ruler in render 10, and the dark blue backdrop are render graphics, not part of the model.

Chibi Doctor Doom in a green hood and cape over steel armor, seen from the front with one boot raised on a ribbed machine block.
Front view cropped tight from the hood to the boots, with the top of the machine block and a corner of the plinth at the bottom right. It's the largest full-body view: rivets, the ring stack on his right upper arm, the gauntlet finger plates and the buckle's scrollwork are all easy to see.
Chibi Doctor Doom standing on a round bronze and concrete base, fists clenched, left boot on a ribbed machine block.
Straight-on front view of the whole statue on its base, centered, level camera. It's the clearest overall view and the only front view that shows the base's lighter stone panels, buttresses and bronze disc in full.
Chibi Doctor Doom on his base holding a glowing blue cube in his open left hand.
The same framing as 02, with his left hand open, palm up, holding a glowing translucent blue cube tilted onto one corner, a pale symbol lit inside it. Only the purple dot shows under "EXCLUSIVE" here. It's the only view of the cube build.
Chibi Doctor Doom from the front right, his hood and mask in profile and his cape flaring behind.
Three-quarter front view from his right, full statue on its base. It shows the mask in side profile (brow plate, nose ridge and cheek vents in relief), how deep the hood sits, and the side of the machine block with its round fitting and a small slotted panel.
The back of chibi Doctor Doom, a green hood and long draped cape over steel boots on a bronze base.
Rear three-quarter view from his right, full statue on its base. It shows the back of the cape with its deep folds and the gathered fold under the hood, the folded tip at the back of the hood, his right gauntlet from behind, and a riveted square plate and a pipe on the back of the plinth.
Chibi Doctor Doom from the back left, his cape draped over the pipes and riveted plates of the base.
Rear three-quarter view from his left, full statue on its base. It's the only clear look at the pipework: pipes with elbow bends, a small box with three slots and riveted plates, plus the raised fist and the left boot on the ribbed block from behind.
Close-up of chibi Doctor Doom's riveted iron mask and orange eyes inside a green hood, gold clasps at his collar.
Close-up of the head and chest from the front, cropped at the belt; the "3D PRINTABLE" lettering overlaps his arm. It shows the mask's detail closest: the rivet row on the brow cap, the eye frames and cheek plates, the eyes' cream whites and orange irises, a pink-lilac reflection on the nose ridge, and the twisted cord between the gold clasps.
Chibi Doctor Doom from the front, fists clenched, cape hanging to his shins.
Front view from the hood to the top of the machine block, framed a touch wider than 01. It adds little that 01 doesn't; it's a second look at the front, with the cape's lower edge on his right fully in frame.
Chibi Doctor Doom seen from above, his green hood and cape spread over a round base.
High three-quarter front view looking down on the statue. It's the only view from above: the top of the hood, the flat round top of the machine block under his boot, the top of the plinth, and how far the cape wraps around him.
Chibi Doctor Doom on his base beside a ruler showing about 15 cm, with a seated Doom figure to the right.
Size render: the standing statue on its base at left, with a ruler down the left edge marked 1 to 21, fine ticks between the numbers and no unit printed. The top of the hood sits just above the 15 mark. On the right is a second Doom, seated with no base and legs out front, in the same green and steel with a gold buckle. Only the purple dot shows under "EXCLUSIVE." It's the only size reference in the set. None of the 13 STLs in this folder matches the seated figure.