Chibi Milo by Chibi Station - Kit Overview

Scorpio Milo from Saint Seiya as a chibi in full gold armor, one finger raised inside a burst of red lightning, on a ruined-temple base with three tiny scorpions.

Share
Full view of Chibi Milo standing on a cracked stone base with a standing column, a fallen column and three small scorpions.

Scorpio Milo from Saint Seiya as a chibi in full gold armor, one finger raised inside a burst of red lightning, on a ruined-temple base with three tiny scorpions. What makes this kit stand out is how much is built around a small figure: a beaded scorpion tail looping off the helmet, a two-tone cape, and a translucent effect part that wraps from his hand up over the helmet crest.

This post is written from the studio's files and renders. I have not printed it yet.

At a glance

  • Studio: Chibi Station
  • Character and source: Milo (Scorpio Milo), Saint Seiya
  • Section: Anime
  • Versions and sizes: One version, the full figure on its rock base. Roughly 22 cm (about 8.5 in) tall to the helmet horns, base included, by my estimate. The rock base is 99.6 × 125.9 mm, and the cape swings out past its edge on his right side by roughly 4 cm, also my estimate. The kit has no dimension sheet, so every size here comes from the STL bounding boxes.
  • Size note: The studio doesn't give an assembled height for this kit. The height here, about 6 to 9 inches, is my estimate from the STL files.
  • Parts: 26 as rendered. The folder holds 27 files; the extra one is a round logo display disc that doesn't appear in any render.
  • Presupports: None. Raw STLs only, with no presupported files and no slicer projects.
  • Largest part and plate fit: Ground.stl, 99.6 × 24.0 × 125.9 mm. Per the STL report, every part fits a Mars-class plate in at least one axis-aligned orientation.
  • Ratings (estimated): Print 4/5, Assembly 4/5, Paint 4/5. Skill: advanced.
  • Status: files reviewed, not printed.
  • Where to get the files: from the studio, Chibi Station.

The model

Milo stands square on a raised stone slab, feet apart, weight even on both legs. His right arm goes up with the elbow bent and the index finger pointing at the sky. An eight-point red star bursts from that fingertip, and jagged red lightning runs down the forearm, crosses in front of his face, and climbs over the crest of his helmet. It's the studio's take on his Scarlet Needle. His left arm is bent at his side with the fist clenched at hip height.

He wears the full gold Scorpio Cloth. The helmet has a V-shaped brow plate, a raised center crest, two long horns that sweep up and out, and gold crescents that curve under each eye. A scorpion tail of gold beads runs from the top of the helmet, around the back of his head, over his right shoulder, and hangs down in front to hip level, ending in a curved gold stinger. The chest plate has radiating ridge lines and a swirl medallion at the sternum. The rounded pauldrons carry scroll engravings and short curved horn spikes. Below that come gold forearm bracers, gold plates over the fingers, a skirt of pointed plates with a raised hook relief on the side panels, crescent ornaments at the hips, shield-shaped knee plates with an oval dome in each, segmented shins, and pointed boots. The upper arms show skin between pauldron and bracer. The cape is white on the outside with a royal blue lining, has a fine fabric grain on both faces, and billows out to his right and down behind him to the base.

The face is classic chibi: a big head and big cyan-blue eyes, half-lidded under a heavy dark lash line, with the brows pulled down and a small mouth set flat. One blue strand falls between his eyes. He looks cool and unimpressed. His hair is long and deep blue, falling in thick tapered locks past his shoulders to the middle of his back, with spiky locks poking up behind the helmet crest.

The base is a slab of cracked stone in stepped layers with a roughly octagonal outline. A broken fluted column stands at his left. A fallen column leans on rubble behind his right side, under the cape. Pale dust puffs curl around both boots. Three small brown scorpions sit around him: one climbing the standing column, one on the ground in front, one down by the fallen column. The cape carries the footprint. It's the widest element and sweeps past the base edge on his right. The raised arm, the red burst and the helmet horns carry the top of the silhouette, and the bead tail fills the gap between the arm and the cape.

Versions and sizes

  • Full figure on rock base (STL/)
    • H × W × L: Roughly 220 mm tall (my estimate); base 99.6 × 125.9 mm; cape overhangs the base by roughly 40 mm on his right (my estimate)
    • Pieces: 26 as rendered, 27 with the logo disc
    • Presupported (format): No (raw STL only)

There's one version. The height is my estimate from stacking the bounding boxes against the renders: 24.0 mm of ground, about 72 mm of the 80.2 mm leg armor showing below the skirt, 66.4 mm of torso armor, and about 55 mm of head, hair and helmet above the collar, for roughly 218 mm. The red effect reaches about another centimetre above the horns.

Who it suits: anyone with a Mars-class printer or bigger, since every part fits one. It suits someone who's comfortable supporting thin effect parts and tiny scenery and who wants to paint a lot of gold. Plan on about 22 cm of shelf height, and a little more width than the base because of the cape.

About the sizes. Every measurement in this post comes from the sculptor's files or the studio's published size information for the unprinted model. A printed kit can differ slightly: resin shrinks a little as it cures, removing supports and sanding takes off some material, and the assembled height depends on how the parts are fitted. Treat the numbers as a close guide, not an exact guarantee.

What's in the download

One folder, STL/, with 27 files. Sizes are bounding boxes in mm (x × y × z, with y up) from the STL report. Left and right are Milo's own: Pillar_left is the column at his left, and Right_arm_armor is the raised arm.

Figure

  • head.stl: Face and neck
    • Size mm: 30.9 × 47.0 × 28.8
    • Notes: Hair and helmet fit over it
  • Top_hair.stl: Front and crown hair: bangs, the strand between the eyes, spiky locks behind the crest
    • Size mm: 48.6 × 39.4 × 46.1
    • Notes: Fine strand tips
  • Back_hair.stl: Long back hair, down to mid-back
    • Size mm: 64.2 × 92.0 × 60.7
    • Notes: Heaviest figure piece; worth hollowing; tapered tips
  • Helmet.stl: Helmet: brow plate, crest and horns; likely also the beaded tail
    • Size mm: 70.6 × 115.9 × 74.9
    • Notes: 115.9 mm is far taller than a helmet alone, which is why I think the tail is modeled on it; thin horn tips
  • Helmet_side.stl: Probably the pair of crescent eye guards
    • Size mm: 31.0 × 21.7 × 19.0
    • Notes: Width matches the 30.9 mm head
  • Torso_armor.stl: Chest plate with medallion, and the skirt of pointed plates
    • Size mm: 44.7 × 66.4 × 46.5
    • Notes: Hollowing candidate
  • Right_shoulder.stl: Right pauldron, raised-arm side
    • Size mm: 27.7 × 33.0 × 26.7
    • Notes: Horn spike
  • Left_shoulder.stl: Left pauldron
    • Size mm: 27.1 × 21.2 × 35.8
    • Notes: Horn spike
  • Right_arm.stl: Small arm part, likely the skin-tone upper arm of the raised arm
    • Size mm: 16.3 × 12.1 × 18.5
    • Notes: I haven't confirmed what this and the other three small arm and leg parts are
  • Left_Arm.stl: Small arm part, likely the skin-tone left upper arm
    • Size mm: 13.5 × 17.9 × 13.7
    • Notes: Not confirmed either
  • Right_arm_armor.stl: Raised forearm bracer with the pointing hand
    • Size mm: 18.0 × 39.4 × 42.3
    • Notes: Thin raised finger; the effect wraps around it
  • Left_arm_armor.stl: Left bracer with the clenched fist
    • Size mm: 33.0 × 26.6 × 28.0
  • Right_leg_armor.stl: Right leg armor, boot upward
    • Size mm: 22.5 × 80.2 × 34.9
    • Notes: Weight-bearing
  • Left_leg_armor.stl: Left leg armor, boot upward
    • Size mm: 22.8 × 75.0 × 25.4
    • Notes: Weight-bearing
  • Right_leg.stl: Small leg part, likely the upper thigh under the skirt
    • Size mm: 16.4 × 21.8 × 17.2
    • Notes: Not confirmed either, like the arm parts
  • Left_leg.stl: Small leg part, likely the upper thigh under the skirt
    • Size mm: 15.3 × 21.6 × 17.3
    • Notes: Not confirmed either

Cloth

  • Cape.stl: Cape, white outside, blue lining
    • Size mm: 99.5 × 114.4 × 84.4
    • Notes: Broad curved sheet; hangs off his back

Accessories

  • Red_lightining1.stl: Red effect: eight-point star and lightning bolts
    • Size mm: 52.4 × 53.7 × 38.2
    • Notes: Studio's spelling; very thin; rendered as translucent red

Base and scene

  • Ground.stl: Cracked rock slab base
    • Size mm: 99.6 × 24.0 × 125.9
    • Notes: Largest part; solid; hollow it
  • Pillar_left.stl: Standing broken fluted column at his left
    • Size mm: 32.6 × 59.3 × 30.0
    • Notes: Hollowing candidate
  • Pillar_right.stl: Fallen column on rubble behind his right side
    • Size mm: 66.1 × 41.0 × 70.6
    • Notes: Hollowing candidate; sits under the cape
  • Cloud_left.stl: Dust puff at his left boot
    • Size mm: 22.0 × 10.7 × 7.7
    • Notes: Small
  • Cloud_right.stl: Dust puff at his right boot
    • Size mm: 29.7 × 12.0 × 13.0
    • Notes: Small
  • Scorpion_Base.stl: Scorpion on the ground, likely the one in front
    • Size mm: 18.4 × 10.9 × 17.4
    • Notes: Thin legs, pincers and tail; fragile
  • Scorpion_Right.stl: Scorpion, likely the one by the fallen column
    • Size mm: 17.4 × 11.0 × 18.0
    • Notes: Fragile
  • Scorpion_left.stl: Scorpion, likely the one climbing the standing column
    • Size mm: 19.3 × 16.8 × 13.0
    • Notes: The only scorpion taller than 11 mm, which fits a climbing pose; fragile

Alternates and optional

  • Base_Disc_logo.stl: Round display disc with a logo
    • Size mm: 114.5 × 10.5 × 114.5
    • Notes: Not in any render; I can't tell whether it goes under the rock base or replaces it

Group counts: Figure, 16 files. Cloth, 1 file. Accessories, 1 file. Base and scene, 8 files. Optional disc, 1 file.

Whole folder: 27 files. One build as rendered, without the disc, is 26 files.

Nothing in the folder is presupported, and there are no slicer project files.

A few odd things in the folder:

  • The logo disc is 114.5 mm across and 10.5 mm thick. The rock base is 125.9 mm on its long side, so if the disc goes underneath, the base overhangs it by about 5.7 mm at each end: (125.9 − 114.5) / 2 = 5.7. The renders show the rock base standing on its own.
  • The effect file ends in "1", but there's no second lightning file. Its 52.4 × 53.7 × 38.2 mm box looks big enough to hold the star and all the bolts the renders show.
  • There are no separate hand files. The fist and the pointing hand look like they're modeled on the arm armor pieces.
  • The renders don't show pegs or sockets, so I can't say which joins are keyed.

4/5 (estimated). This kit ships raw only, so you support it yourself.

Plate fit isn't the problem. Per the report, every part fits a Mars-class plate in at least one axis-aligned orientation. The biggest footprints are Ground.stl at 99.6 × 24.0 × 125.9 mm and, if you print it, the disc at 114.5 × 10.5 × 114.5 mm.

The 4 comes from thin parts and one big curved sheet.

Red_lightining1.stl is spread thin across a 52.4 × 53.7 × 38.2 mm box. That's narrow jagged bolts and eight tapered star points with very little mass behind any of them. It needs careful orientation and a lot of light supports, and it's the part most likely to snap on support removal. The renders show it in translucent red, so clear red resin is the natural choice.

The three scorpions are tiny, 17 to 19 mm long, with legs, pincers and curled tails. I'd print a couple of spares of each.

Cape.stl is 99.5 × 114.4 × 84.4 mm: a broad, curved sheet, the cupped kind of surface that causes suction. Angle it so the hollow of the curve doesn't face the vat floor.

The helmet horns taper to points. If the bead tail is on the helmet, as its 115.9 mm height suggests, that's a long chain of balls hanging off the part, and each bead wants its own support.

The raw files are solid. Ground.stl is the largest solid part, and I'd hollow it with drain holes. Also worth hollowing: Cape.stl, Back_hair.stl, Torso_armor.stl, Pillar_right.stl and Pillar_left.stl. The disc, if you use it, is large and solid too.

Why not a 5: nothing exceeds a Saturn-class plate, and nothing has to be hollowed to print at all.

Assembly difficulty

4/5 (estimated). It's 26 parts as rendered, which puts it in the 20-plus range.

The figure alone is 16 parts: two leg armor pieces and two small leg parts, the torso, two pauldrons, two small arm parts, two forearm pieces, the head, two hair pieces, the helmet and the helmet side piece.

The figure stands on two boots, and the leg armor carries everything above it. Each leg armor piece is far lighter than the torso, the back hair or the cape, which are all solid as supplied. I'd pin both legs into the base and the torso onto the legs. Order matters here. The sequence I'd plan is legs into the base, then torso, arms and pauldrons, head, hair, helmet and cape, with the effect last.

There are two hanging pieces. The cape hangs off his back and swings out past the base edge, and the bead tail hangs in front of his right side. The cape falls over the fallen column, so dry-fit the column and cape together before gluing either one.

The red effect is the most delicate join. It touches the raised hand and the helmet crest, and the contact points are as thin as the bolts. It goes on last, after the helmet. Helmet_side.stl frames the face and is small to handle.

Top_hair.stl and Back_hair.stl meet somewhere in the hair mass. The renders don't show where, so expect to fill a seam running through the strands.

The base is eight pieces of its own: the ground slab, two columns, two dust puffs and three scorpions. The scorpions are under 20 mm and fiddly to place.

Paint difficulty

4/5 (estimated). There are a lot of materials. Gold metal covers most of the figure. Then there's blue hair, skin on the face, upper arms and finger tops, anime eyes, a two-tone cape with a fabric grain, a translucent red effect, gray stone, pale gray columns, brown scorpions and pale dust puffs. That's seven or more materials.

The gold is the biggest job. The chest, skirt, leg armor and helmet are big smooth plates, and metallic gold shows every brush mark and uneven coat. An airbrush or a well-thinned metallic helps. The engraved lines and plate edges want a darker wash to separate the plates.

The face is a cartoon face, but the eyes are freehand on a 31 mm wide head. Each eye has a cyan iris that darkens toward the top, a black pupil, white catchlights and a near-black lash line.

The cape has two painted faces on one thin sheet, white outside and royal blue inside. It's easier to paint both before it goes on.

The red effect needs little paint if you print it in clear red resin. In clear resin, it takes a candy red.

The base is drybrush-friendly stone. The scorpions are tiny but only need two browns.

Why 4 and not 5: the translucent effect is the kind of thing that pushes toward 5, but the face is cartoon style and skin is a small share of the figure. Why not 3: there are four-plus materials, freehand eyes, and a lot of large smooth gold.

Paint reference. These are the studio's colors from the renders, material by material:

  • Gold Cloth (armor, helmet, bead tail and stinger): saturated lemon-to-warm gold, with bright yellow highlights on the curves and a deeper ochre gold in the recesses and engraved lines.
  • Hair: deep royal blue running to violet-blue, with lighter periwinkle highlights along the strand tops. The eyebrows match the hair.
  • Skin (face, upper arms, finger tops): pale porcelain peach with soft pink shading.
  • Eyes: bright cyan-blue iris darkening toward the top, black pupil, white catchlights, and a near-black upper lash line.
  • Mouth: a thin, muted pink-brown line.
  • Cape: off-white to light gray outside, vivid royal blue lining, with a white edge where the two meet.
  • Effect: glossy translucent crimson, darker where the part is thicker.
  • Ground: cool mid-gray stone, darker in the cracks and lighter on the edges.
  • Columns: light gray, a shade paler than the ground.
  • Scorpions: dark chocolate brown with lighter tan-brown on the segment edges.
  • Dust puffs: pale gray-white.

All ten are studio renders. The round Chibi Station logo badge in the bottom right, the "3D PRINTABLE / SCORPIO MILO" lettering in the bottom left, and the dark gradient backdrop are render graphics, not part of the model.

Chibi Milo in gold armor raises one finger inside a red star burst, his blue-lined cape flaring beside a broken stone column with a scorpion on it.
Front three-quarter from slightly to his left, cropped tight so the figure fills the frame from the horn tips down, with the base cut off at the bottom edge. You can see the raised arm with the red star and lightning, the bead tail hanging to hip level, the cape flaring wide to his right with its blue lining and white edge, the left fist, the standing column with a scorpion climbing it, two more scorpions on the ground, and dust puffs at both boots. It's the largest full-figure view, and the clearest look at the knee plates, shin segments, boots and the climbing scorpion.
Close-up of Milo's stern face under a gold horned helmet, with red lightning crossing over the crest.
Close-up of the head and helmet from the front, with the red star cut off at the left edge and a bit of pauldron and chest at the bottom. It shows the eyes up close (cyan iris, dark lash line, white catchlights), the blue strand between the eyes, the crescent eye guards, and how the lightning runs over the helmet crest and past his face. It's the best view of the face and of how thin the effect bolts are.
Full view of Chibi Milo standing on a cracked stone base with a standing column, a fallen column and three small scorpions.
Full figure and full base, front three-quarter from his left, pulled back with room around it. It shows the whole stepped stone base with its roughly octagonal outline, all three scenery groups (standing column, fallen column, scorpions) and the cape swinging out past the base edge. It's the only render that shows the whole build uncropped with margin, and it's the feature image.
Milo seen from his left side with fist clenched and long blue hair streaming back, a broken column in front of him.
Front three-quarter from his left side, full figure and base, with the standing column in the right foreground. It shows the side of the helmet and crest, the curved horn spikes on both pauldrons, the scroll engravings on the shoulder plates, the left fist from the side, the long hair streaming back, and the cape's white outer face starting to show behind him. It's the clearest view of the pauldron spikes and of how deep the hair is.
Side profile of Milo facing left, the gold bead tail looping off his helmet and his white cape trailing behind to the base.
Left profile, full figure and base, with the standing column in the foreground hiding his lower leg. It shows the bead tail arcing off the top of the helmet and down in front, the white cape trailing far behind him to the rubble, the full length of the hair, and a scorpion near the front edge of the base. It's the only render that shows the figure's depth front to back.
Rear view of Milo with long blue hair and a white cape, the gold bead tail running down his back.
Straight rear view, full figure and base. It shows the back of the hair in long tapered locks, the bead tail running down the back of the hair and off over his right shoulder, the white outer face of the cape with its fine grain falling over the fallen column, both columns from behind, and a scorpion by his heel. It's the only straight-on back view, and the only good look at the back of the base.
Milo from behind on his right, the beaded scorpion tail looping around his head and his cape folding over a broken column.
Rear three-quarter from his right side, full figure and base. It shows the full loop of the bead tail around the back of his head and over the shoulder to the stinger, the cape's lower edge curling so the white outside and blue lining show together, the back of the skirt and leg armor, a dust puff at the heel, and scorpions on a column and on the ground. It's the best view of the tail's whole path and of the two-tone cape fold.
Front view of Milo in gold armor on a cracked rock base, three scorpions around his feet.
Front three-quarter from his left, full figure and base, at nearly the same angle as 03 but closer and a little lower. It shows the cracks in the front base slabs, the skirt plates and knee plates at a larger size, and all three scorpions in view at once. It's the same pose as 03 with more detail on the base and the scorpion placement.
Close-up of Milo's face and gold chest armor, his raised hand inside a red star burst.
Close-up of the head and chest from the front, slightly to his left, with the red star at the left edge and the left fist at the right edge. It shows the chest plate's ridge lines and swirl medallion, the pauldron engravings, the skin of the raised upper arm between pauldron and bracer, the bead chain coming down in front, and the stern face. It's the clearest view of the chest armor and of how the raised arm meets the shoulder.
Low-angle view of Milo in gold armor and a blue cape, raising a finger wrapped in red lightning.
Front view from a low angle on a darker backdrop, cropped from the red effect down to the boots, with the base mostly out of frame. It shows the raised arm and effect from below, the hook relief on the skirt's side panels, the crescents at the hips, the knee plates, the grain of the blue cape lining, the gold plates on the fist's fingers, and the column with its scorpion. It's the only low-angle view and the clearest on the skirt relief and the fist.