Beta by Moon Figures - Kit Overview

Moon Figures' Beta mid-leap on a slab of cracked stone, bow in hand and cloak streaming. Sixteen numbered parts, one render, a Chitubox project, and a solid stone base 172 mm across.

Share
A silver-haired elf archer in a black and gold bodysuit leaps on one heel across a round cracked-stone base, bow in hand and a long dark cloak streaming behind her.

Beta, from That Time I Got Reincarnated as a Slime, by Moon Figures. A silver-haired archer caught mid-stride on one heel, right arm thrown back, bow in the left hand and a long dark cloak whipping out behind her, all on a round slab of broken paving stone. What stands out in the files is the base: one solid disc, 172 mm across, that needs hollowing and drain holes.

This post is written from the studio's files and the one render they ship. I have not printed it yet. Everything below is checkable against the download, and where the render can't settle something, I say so.

At a glance

  • Studio: Moon Figures (the download folder is named Moon Prints).
  • Character and source: Beta, That Time I Got Reincarnated as a Slime (Tensura).
  • Section: Anime.
  • Versions and sizes: one version, in stl/. No dimension sheet in the download, so sizes are STL bounding boxes: the base Beta_0.stl is 171.2 × 38.5 × 172.5 mm (H 38.5, W 171.2, L 172.5 — a disc about 172 mm across); the tallest single part is the bow Beta_7.stl at 156.0 mm; the longest body part is 130.8 mm. Assembled height is not stated by the studio. My rough estimate from the render's proportions against the 172 mm base is somewhere around 220–240 mm to the top of the bow, base included.
  • Size note: The studio doesn't give an assembled height for this kit. The height here, about 9 to 12 inches, is my estimate from the STL files.
  • Parts: 16 numbered STLs, Beta_0.stl through Beta_15.stl.
  • Presupports: no presupported STLs. One stl/Beta.chitubox project file, the studio's supported and plated scene, which only opens in Chitubox.
  • Largest part and plate fit: Beta_0.stl, 171.2 × 38.5 × 172.5 mm. Misses Mars-class (143 × 90 × 175 mm). Fits Saturn-class (219 × 123 × 250 mm), but only stood on its edge — 172.5 mm is too long for the 123 mm plate depth if you lay it flat. Every other part fits Mars-class.
  • Ratings (estimated): Print 4/5, Assembly 4/5, Paint 3/5. Skill tag: advanced.
  • Decals: Decals/eyes_Delta.psd, a Photoshop file of printable eye decals. The studio named it "Delta" rather than "Beta"; it's the only decal file in the folder, so I'm treating it as this kit's eyes.
  • Status: files reviewed, not printed.
  • Where to get the files: Moon Figures' Patreon and Gumroad store, linked at the bottom.

The model

Moon Figures ships a single render, so everything I can say about the sculpt comes from that one image and the part list.

The pose is a leap or a long running stride. Beta is up on the toe of her right heel, planted on a raised rock at the right side of the base, with the left leg kicked up and back behind her so the left foot hangs in the air near the lower tip of the bow. The torso twists toward the camera and leans forward. Her right arm is flung back and up behind her head, the gloved hand open with the fingers spread. Her left arm drops straight down her side to grip a long bow at its middle, so the bow runs on a diagonal from below the trailing foot to well above her head. I don't see a bowstring modeled in the render, and I haven't checked whether Beta_7.stl has one.

The identifying details are the hair and the ears. The hair is a short bob in a pale silver with a faint blue cast, with a thin braid running down the left side of the face and a fringe cut straight across the brow. The ears are long and pointed. The face is a standard anime face: large blue eyes with a lighter highlight, thin brows, a small nose, and an open mouth with red lips, as if she's calling out mid-stride. The skin is pale with a slight cool tint in the render.

The costume, item by item from the render: a dark, near-black bodysuit that covers her from chest to ankle, with a slight sheen on the surface. Over the chest sits a fitted plate with a sweetheart bust line, edged in gold, and a gold collar piece at the throat. A short dark shoulder mantle covers the upper arms, also edged in gold. At the waist is a belt with gold trim and a small gold diamond ornament hanging at the left hip, with a second gold-edged plate on the right hip. The gloves are dark and reach the wrist. The boots are thigh-high, dark, with a high stiletto heel, a gold band at the top of each and a gold plate on the heel. The cloak is the biggest single element visually: a long dark wrap that leaves the shoulders, billows up behind her and then splits into two tails that stream out to the right, each ending in a gold cap set with a purple diamond gem. The bow is a dark gray-green with gold-edged limbs and perforated gold tips at both ends.

The base is a round disc of cracked paving stone. Broken flagstones cover most of the surface, with a mound of rubble and a larger boulder at the right, where her planted foot lands. In the render the whole base is a single flat olive-khaki material with no color scheme applied, so the studio isn't telling you what color to make it.

The silhouette is wide rather than tall. The cloak tails reach about to the edge of the disc on the right, and the bow runs the full height of the figure and then some. The base disc carries the footprint; the figure touches it at exactly one point, the right heel.

Versions and sizes

  • stl/ (only version)
    • H × W × L (mm): Base 38.5 × 171.2 × 172.5; tallest part 156.0 (bow); assembled height not stated
    • Pieces: 16
    • Presupported (format): No separate presupported STLs — supported scene in stl/Beta.chitubox (Chitubox project)

Sizes are STL bounding boxes; there is no dimension sheet in the download.

There is only one version, so there's no small-or-large choice to make. Who it suits: someone with a Saturn-class or larger printer, or someone on a Mars-class printer who is willing to cut the base disc into two halves and rejoin it. If you print in Chitubox you get the studio's supports and plating as they set them; if you slice in Lychee or anything else you're supporting sixteen raw, solid parts yourself.

About the sizes. Every measurement in this post comes from the sculptor's files or the studio's published size information for the unprinted model. A printed kit can differ slightly: resin shrinks a little as it cures, removing supports and sanding takes off some material, and the assembled height depends on how the parts are fitted. Treat the numbers as a close guide, not an exact guarantee.

What's in the download

Parts are numbered, not named, so the description after each file name is my inference from each part's size against the render. The confident entries are the base, the bow, the torso and the two legs. Everything else is a best guess.

Version: stl/

Figure

  • Beta_3.stl
    • What it is (inferred): Torso — chest to hips, bodysuit and chest plate
    • Size mm (X × Y × Z): 38.0 × 74.9 × 38.8
    • Notes: Densest body part; the core everything else pegs into. I can't tell from the render what the pegs or sockets look like.
  • Beta_13.stl
    • What it is (inferred): Planted right leg, hip to heel, thigh boot
    • Size mm (X × Y × Z): 53.0 × 130.8 × 56.2
    • Notes: Longest body part. Single contact with the base at the heel — load-bearing.
  • Beta_10.stl
    • What it is (inferred): Trailing left leg, bent, thigh to boot
    • Size mm (X × Y × Z): 38.1 × 71.5 × 54.6
    • Notes: Hangs free in the air behind her.
  • Beta_14.stl
    • What it is (inferred): Head — face and neck
    • Size mm (X × Y × Z): 23.7 × 31.7 × 22.5
    • Notes: Compact and solid for its box; eyes are decals.
  • Beta_5.stl
    • What it is (inferred): Hair — the silver bob, as a shell over the head
    • Size mm (X × Y × Z): 34.4 × 35.3 × 42.2
    • Notes: Thin for its box, which is what a hair shell looks like.
  • Beta_11.stl
    • What it is (inferred): Right arm, bent and raised behind the head
    • Size mm (X × Y × Z): 32.7 × 34.5 × 31.8
    • Notes: Compact box suits a bent arm. It could be the shoulder mantle instead.
  • Beta_4.stl
    • What it is (inferred): Left arm, straight down to the bow grip
    • Size mm (X × Y × Z): 23.6 × 20.8 × 58.8
    • Notes: Thin, 59 mm long.
  • Beta_8.stl
    • What it is (inferred): Small pair, part 1 — a hand, or an ornament
    • Size mm (X × Y × Z): 9.1 × 16.6 × 11.3
    • Notes: Tiny. They seem small for hands on this figure and may be the cloak-tip caps or the hip ornaments.
  • Beta_9.stl
    • What it is (inferred): Small pair, part 2 — matches Beta_8.stl
    • Size mm (X × Y × Z): 9.9 × 13.9 × 9.5
    • Notes: Tiny.

Cloth

  • Beta_1.stl
    • What it is (inferred): Cloak section — wide and flat, likely the upper billow
    • Size mm (X × Y × Z): 89.3 × 92.7 × 38.5
    • Notes: Thin sheet across a 90 × 93 mm box. Fragile.
  • Beta_2.stl
    • What it is (inferred): Cloak section — the two streaming tails with gold caps
    • Size mm (X × Y × Z): 90.4 × 60.9 × 81.7
    • Notes: Thin sheet, like Beta_1.stl. Fragile.
  • Beta_6.stl
    • What it is (inferred): Shoulder mantle or collar piece
    • Size mm (X × Y × Z): 27.5 × 23.8 × 35.0
    • Notes: Small, thin. It could also be the braid or a hip plate.

Base and scene

  • Beta_0.stl
    • What it is (inferred): Round cracked-stone base with rubble mound and boulder
    • Size mm (X × Y × Z): 171.2 × 38.5 × 172.5
    • Notes: Large solid disc. Misses Mars-class; fits Saturn-class on edge only. Hollow it.

Accessories

  • Beta_7.stl
    • What it is (inferred): Bow, full length
    • Size mm (X × Y × Z): 83.9 × 156.0 × 81.4
    • Notes: Long and thin: 156 mm tall. Fragile.
  • Beta_12.stl
    • What it is (inferred): Thin rod, 39 mm — braid, belt strap or bow fitting
    • Size mm (X × Y × Z): 13.8 × 38.9 × 13.3
    • Notes: I can't identify it from the render.
  • Beta_15.stl
    • What it is (inferred): Hip plate with the gold diamond ornament
    • Size mm (X × Y × Z): 24.9 × 29.3 × 24.0
    • Notes: I haven't confirmed what this part is.

Alternates: none. There are no alternate heads, hands or faces in the folder.

Presupports: none as separate STLs. The stl/Beta.chitubox project holds the studio's supported and plated scene. I can't open a Chitubox project in Lychee, so I can't tell you how the studio oriented the base or which parts they hollowed. If you slice in Chitubox, open that project first and check it against the raw files before you print.

Odd things in the folder: two. The decal file is Decals/eyes_Delta.psd — Delta, not Beta. It's the only decal in the kit and it's the eye-decal sheet Moon Figures always ships, so I'm reading the name as a studio slip rather than a wrong file; confirm it in Photoshop before printing the decals. And Beta_8.stl and Beta_9.stl are tiny, about 9 to 17 mm on a side — small for hands on this figure, and if they're something else I can't tell what from one render.

4/5, estimated. Two things push it there.

The first is Beta_0.stl. It is a 171.2 × 172.5 mm disc, 38.5 mm thick, solid, and it does not fit a Mars-class plate at all. On Saturn-class it fits only on its edge: 172.5 mm is longer than the plate's 123 mm depth, so it has to stand up with the 171.2 × 38.5 mm face on the plate and 172.5 mm going up the Z axis. A disc printed on edge is a tall print with a lot of surface hanging off supports. It's a large solid part; you'll want to hollow it, which means drain holes on the underside and a hollow shell 172 mm tall. On a Mars-class printer the only route is to split the disc in two and hide the seam in a paving-stone crack.

The second is the thin stuff. The cloak is two sheets, Beta_1.stl across an 89 × 93 mm box and Beta_2.stl across a 90 × 61 × 82 mm box. That's a lot of area at very little thickness: support scarring on one face and a real chance of warping if supports are light. The bow, Beta_7.stl, is 156 mm long, a thin diagonal that needs supports along its limbs whichever way it lies. The trailing leg Beta_10.stl has a stiletto heel and a pointed toe hanging in space.

What keeps it from a 5: nothing exceeds Saturn-class, the files have no degenerate triangles, and the studio has done a supported and plated scene in Chitubox. Use that project as-is on a Saturn-class printer and most of this is decided for you. Studio hollowing: I can't see it, because there are no presupported STLs to compare against the raw files; if it exists it's inside the .chitubox file.

Assembly difficulty

4/5, estimated. Sixteen parts is inside the 10–20 range that normally reads as a 3, but three things about this pose push it up.

The whole figure stands on one heel. Beta_13.stl is the planted right leg, and the only contact between the figure and Beta_0.stl is the tip of a stiletto heel on a boulder. Above that heel sits everything else — the rest of the figure, the bow and the cloak. I'd treat a brass pin through the heel into the rock as not optional, and I'd pin the hip joint too. I haven't checked whether the studio modeled a peg at the heel or the sole.

The cloak is two large thin sheets that attach at the shoulders and back and hang out to the right with nothing under them. That's a cantilever on a thin part with a small glue face. Expect to pin the cloak into the back of the torso and to align the two sections so the tails read as one piece of cloth; the seam between Beta_1.stl and Beta_2.stl will sit on a smooth surface.

The bow is 156 mm long and held at one point by the left hand. Beta_4.stl is a thin arm; the grip has to carry the bow, and the bow's lower tip hangs near the trailing foot with no support.

The rest is ordinary: head into torso, hair over head, two legs into the hips, and five small parts (Beta_6.stl, Beta_12.stl, Beta_15.stl, Beta_8.stl, Beta_9.stl) small enough to lose. Whether the joins are keyed pegs or flat faces I can't tell from a render.

Paint difficulty

3/5, estimated. The materials count is high enough to argue for a 4, but the surfaces are mostly large and flat, the face is anime rather than realistic, and the eyes come as waterslide decals in Decals/eyes_Delta.psd, so there's no freehand eye painting.

What takes the time: the gold trim. It runs along the bust line, the collar, the mantle edge, the belt, both hip plates, both boot cuffs, both heels, both cloak caps, and both bow tips — thin lines on a dark ground, where a wobble shows. The purple gems in the cloak caps are small and want a highlight. The hair is a pale silver with a blue cast, which is a wash-and-highlight job on a bob with a braid; the braid is fine detail. The skin is limited to the face, chest, and midriff, all flat anime skin.

What's easy: the bodysuit, gloves, boots and cloak are all the same near-black with a slight sheen, so most of the figure is one base coat and one highlight pass. The base is cracked stone and rubble, which is a drybrush job of whatever stone color you choose; the render gives you no scheme for it.

Paint reference, from the studio's render, material by material: hair pale silver-white with a faint blue cast, darker in the recesses; skin pale with a slight cool tint; eyes blue with a lighter blue highlight (decal); lips red, mouth open; bodysuit, gloves, mantle and thigh boots a near-black with a soft satin sheen; chest plate, collar, belt, hip plates, boot cuffs, heel plates and cloak caps a warm metallic gold; hip ornament gold with a purple-red gem; cloak the same near-black as the suit, with a dark violet cast in the folds; cloak caps gold with a purple diamond gem in each; bow a dark gray-green body with gold-edged limbs and perforated gold tips; base a single flat olive-khaki in the render, which reads as unpainted rather than a chosen color.

Moon Figures ships a single render for this kit, so this is the only image.

A silver-haired elf archer in a black and gold bodysuit leaps on one heel across a round cracked-stone base, bow in hand and a long dark cloak streaming behind her.
Full-figure color view from slightly below eye level and a little to her left, dark background, Moon Figures logo top left. Beta up on her right heel on the boulder at the right of the base, left leg kicked back, right arm flung up behind her head with the fingers spread, left hand gripping the bow at its middle so it runs diagonally from below the trailing foot to above her head. The cloak billows up behind the shoulders and streams out to the right in two gold-capped tails. The whole base disc is in frame, showing the flagstone cracks, the rubble mound and the boulder, all in a single flat olive-khaki. It shows the only thing any image can here — the full color scheme, the pose from one angle and how the figure sits on the base — but it doesn't show the back of the cloak, the right side of the face, or the underside of the base.