Danua by Moon Figures - Kit Overview

Danua from Granblue Fantasy, leaning on a stone pillar with her doll at her feet. A 31-part Moon Figures kit on a 126 mm base, written up from the files and the render before anything is printed.

Share
Rendered figure of Danua from Granblue Fantasy in a white dress and black corset, seated against a fluted stone column with a small doll at its base on a round flagstone disc.

Danua, from Granblue Fantasy, by Moon Figures.

What stands out in this kit is the scene rather than the pose. Danua leans against a fluted sandstone column, her long black hair streaming out behind her, with a small doll slumped at the foot of the column. It is a seated, quiet figure that gets its drama from the hair and the stained hem of the dress, and the studio has split it into 31 numbered parts on a single 126 mm base.

This post is written from the studio's files and the one render they ship. I have not printed, built, or painted this kit yet. Where the image or the STL data cannot settle something, I say so.

At a glance

  • Studio: Moon Figures
  • Character and source: Danua, Granblue Fantasy
  • Section: Fan art
  • Versions and sizes: one version. No dimension sheet ships with the kit; from the STL bounding boxes the base disc is 126.2 mm across and the largest body part measures 116.0 mm along its longest axis, which puts the assembled figure somewhere in the 130–150 mm range on a 126.2 × 126.2 mm footprint.
  • Size note: The studio doesn't give an assembled height for this kit. The height here, about 3 to 6 inches, is my estimate from the STL files.
  • Parts: 31 numbered STLs (Danua_0.stl through Danua_30.stl)
  • Presupports: the studio's supported and plated project ships as stl/Danua.chitubox, a Chitubox project file. There are no separate presupported STLs.
  • Largest part and plate fit: Danua_0.stl, the base disc, at 126.2 × 5.0 × 126.2 mm. Every part fits Mars-class; nothing needs a Saturn-class plate.
  • Ratings (estimated): Print 3/5, Assembly 5/5, Paint 4/5 → advanced
  • Eyes: a Photoshop decal file, Decals/eyes_Danua.psd, for waterslide eye decals
  • Status: files reviewed, not printed
  • Where to get the files: Moon Figures' Patreon and Gumroad store, linked at the bottom.

The model

Moon Figures ships a single render for this kit, so everything below comes from that one image and the part list.

Danua is perched on the edge of a stone slab that sits on a short fluted column. Her weight is on the slab and her right forearm rests along its top, fingers curled over the edge. Her left arm hangs down beside her, and that bare hand is visible on the tiled floor at the left of the base, half hidden by the hem of the dress. One sandalled foot shows below the hem at the front, heel down, toes forward. The body language is relaxed, almost tired, and the head tilts slightly toward the camera with a small closed-mouth smile and red eyes looking straight out. The ears are pointed. Two short curved horns, a reddish brown, grow from the sides of the head, and each carries a hanging ornament: on the left horn a spike-shaped drop with a crescent moon below it, on the right a similar spiked drop on a short chain. A single ahoge stands up from the crown.

The hair is the biggest element in the render. It is black with cool grey highlights, parted over the forehead with long bangs framing the face, and the rest sweeps out to the right of the figure in a wind-blown mass that reaches well past the column and almost to the edge of the base. Several separate locks peel off the main mass and curl back on themselves. In the parts list this shows up as one large 93.8 mm part plus a handful of long thin pieces, which I read as the hair mass and the individual locks, though the numbered files do not say so.

Costume, item by item. The dress is white, floor length, gathered at the bust and falling in heavy folds over the lap and down to the floor. The hem is dirty: soft grey-brown smudges climb the lower skirt and the underside of the hem, where it turns up, reads darker, closer to a dull red-brown. Over the waist sits a black corset with raised silver scrollwork across the front. At the neckline there is a small red gem pendant on a thin cord. The right arm is wrapped from bicep to wrist in white bandages, layered with a bit of frayed edge at the elbow, ending in a black fingerless glove with the fingertips bare. The sandal is black with straps over the toes and around the ankle and a low heel.

The doll sits on the tiles at the base of the column, arms out at its sides, legs straight ahead. It has long straw-blonde hair with a green cast, a white hat with a red band and a small red flower, a red and pink dress with a yellow cross on the front, and purple-and-cream striped stockings with dark shoes. Its face is painted flat with simple dark eyes and a small mouth. It is small next to Danua, roughly knee height, and it is the part of the kit most likely to test a fine brush.

The base is a round sandstone disc scored into irregular flagstones, the same warm tan as the column. The column has a plain square foot, a fluted shaft, and a wide flat slab on top that Danua sits on. The silhouette is wide rather than tall: the seated body, the slab and column on the right, and the hair sweeping out beyond them carry the footprint, and the base disc at 126.2 mm is what sets the plate size.

Versions and sizes

  • Standard (only version)
    • H × W × L (mm): approx. 130–150 (est.) × 126.2 × 126.2
    • Pieces: 31
    • Presupported: stl/Danua.chitubox (Chitubox project, no separate supported STLs)

There is one version. The height is my estimate from the render's proportions against the 126.2 mm base disc; the split parts do not give an assembled height directly, and the largest body piece is 116.0 mm along its longest axis.

Who it suits: a printer with a Mars-class or larger plate who is comfortable with a 30-plus part build and a decal-based face. The doll and the horn ornaments are small enough that this is not a first kit. If you only have Chitubox, you get the studio's orientations and supports for free; if you slice in Lychee you are supporting 31 raw STLs yourself.

About the sizes. Every measurement in this post comes from the sculptor's files or the studio's published size information for the unprinted model. A printed kit can differ slightly: resin shrinks a little as it cures, removing supports and sanding takes off some material, and the assembled height depends on how the parts are fitted. Treat the numbers as a close guide, not an exact guarantee.

What's in the download

The 31 STLs are numbered, not named, so the description after each file name below is inferred from each part's size against the render. Danua_0.stl is plainly the base disc and Danua_23.stl is plainly the main body. Everything else is my best reading, and where the render cannot settle something, I say so.

Figure

  • Danua_23.stl
    • What it is (inferred): Main body: seated torso and dress
    • Size mm (X × Y × Z): 84.5 × 80.7 × 116.0
    • Notes: Largest solid part; will want hollowing if sliced from the raw STL
  • Danua_30.stl
    • What it is (inferred): Hair mass sweeping right
    • Size mm (X × Y × Z): 93.8 × 80.4 × 73.1
    • Notes: I can't tell from the render whether this is the hair mass or the skirt's outer flare; widest part in the kit
  • Danua_16.stl
    • What it is (inferred): Upper head and hair crown with ahoge
    • Size mm (X × Y × Z): 38.4 × 55.3 × 32.3
    • Notes: Could instead be the doll in one piece
  • Danua_2.stl
    • What it is (inferred): Head / face
    • Size mm (X × Y × Z): 31.1 × 23.2 × 18.4
    • Notes: Eyes go on as decals
  • Danua_12.stl
    • What it is (inferred): Bangs and front hair, or bust section
    • Size mm (X × Y × Z): 34.4 × 38.4 × 23.1
  • Danua_1.stl
    • What it is (inferred): Bandaged right forearm and glove
    • Size mm (X × Y × Z): 28.9 × 49.8 × 18.8
    • Notes: Could instead be a hair lock
  • Danua_24.stl
    • What it is (inferred): Hair lock
    • Size mm (X × Y × Z): 11.4 × 45.4 × 24.4
    • Notes: Thin, long
  • Danua_25.stl
    • What it is (inferred): Hair lock
    • Size mm (X × Y × Z): 12.8 × 44.1 × 32.7
    • Notes: Thin, long
  • Danua_5.stl
    • What it is (inferred): Hair lock
    • Size mm (X × Y × Z): 14.8 × 36.2 × 18.2
    • Notes: Thin
  • Danua_18.stl
    • What it is (inferred): Hair lock or left arm
    • Size mm (X × Y × Z): 24.8 × 36.2 × 23.6
  • Danua_22.stl
    • What it is (inferred): Hand or glove
    • Size mm (X × Y × Z): 21.5 × 17.8 × 21.2
    • Notes: Could instead be the doll's body
  • Danua_10.stl
    • What it is (inferred): Horn
    • Size mm (X × Y × Z): 25.3 × 14.5 × 16.1
    • Notes: Fragile tip
  • Danua_14.stl
    • What it is (inferred): Horn
    • Size mm (X × Y × Z): 28.0 × 16.1 × 19.4
    • Notes: Fragile tip
  • Danua_8.stl
    • What it is (inferred): Hand
    • Size mm (X × Y × Z): 9.7 × 15.4 × 13.7
  • Danua_11.stl
    • What it is (inferred): Hand
    • Size mm (X × Y × Z): 10.3 × 14.8 × 16.6
  • Danua_15.stl
    • What it is (inferred): Hand or foot
    • Size mm (X × Y × Z): 7.7 × 16.5 × 18.9
  • Danua_19.stl
    • What it is (inferred): Foot in sandal
    • Size mm (X × Y × Z): 18.9 × 10.2 × 15.1
  • Danua_21.stl
    • What it is (inferred): Foot in sandal
    • Size mm (X × Y × Z): 17.9 × 10.4 × 13.6
  • Danua_3.stl
    • What it is (inferred): Sandal sole or strap
    • Size mm (X × Y × Z): 15.4 × 12.3 × 6.6
    • Notes: Flat
  • Danua_4.stl
    • What it is (inferred): Sandal sole or the doll's hat
    • Size mm (X × Y × Z): 18.3 × 25.0 × 6.6
    • Notes: Flat
  • Danua_6.stl
    • What it is (inferred): Strap or hat brim
    • Size mm (X × Y × Z): 17.8 × 8.8 × 6.5
    • Notes: Flat, small

Companion (the doll)

I could not pin the doll to specific numbers. The candidates by size are Danua_16.stl (38.4 × 55.3 × 32.3 mm, if the doll is one piece), or a set built from Danua_22.stl, Danua_9.stl, Danua_4.stl and Danua_6.stl if it is split into body, head, hat and brim.

  • Danua_9.stl
    • What it is (inferred): Doll head, or the column's capital/foot
    • Size mm (X × Y × Z): 15.9 × 27.4 × 15.9
    • Notes: Square footprint

Base and scene

  • Danua_0.stl
    • What it is (inferred): Round flagstone base disc
    • Size mm (X × Y × Z): 126.2 × 5.0 × 126.2
    • Notes: Large flat plate, 5 mm thick; suction risk if printed flat
  • Danua_20.stl
    • What it is (inferred): Column top slab
    • Size mm (X × Y × Z): 88.3 × 19.8 × 49.0
    • Notes: Could instead be a hair section; the seated body rests on it
  • Danua_28.stl
    • What it is (inferred): Fluted column shaft, segment
    • Size mm (X × Y × Z): 23.9 × 51.8 × 23.9
    • Notes: Matches Danua_29.stl almost exactly
  • Danua_29.stl
    • What it is (inferred): Fluted column shaft, segment
    • Size mm (X × Y × Z): 23.9 × 51.8 × 23.9
    • Notes: Stacks with Danua_28.stl for a shaft of about 104 mm

Accessories (horn ornaments and pendant)

  • Danua_7.stl
    • What it is (inferred): Spiked horn drop
    • Size mm (X × Y × Z): 10.2 × 7.1 × 15.4
    • Notes: Tiny
  • Danua_13.stl
    • What it is (inferred): Crescent moon ornament
    • Size mm (X × Y × Z): 14.3 × 6.5 × 14.4
    • Notes: Flat crescent
  • Danua_17.stl
    • What it is (inferred): Spiked horn drop
    • Size mm (X × Y × Z): 8.7 × 5.1 × 14.3
    • Notes: 5 mm thick
  • Danua_26.stl
    • What it is (inferred): Ornament link or pendant gem
    • Size mm (X × Y × Z): 3.5 × 5.8 × 8.2
    • Notes: Smallest parts in the kit; easy to lose in the wash
  • Danua_27.stl
    • What it is (inferred): Ornament link or pendant gem
    • Size mm (X × Y × Z): 3.0 × 6.4 × 8.6
    • Notes: As above

Alternates: none. There are no alternate heads, arms, or clothing states in the folder.

What's presupported: nothing as separate STLs. The studio's supports and plate layout exist only inside stl/Danua.chitubox, so you need Chitubox to see them. All 31 meshes are clean (no NaN triangles) and every part fits Mars-class.

Odd things in the folder: the numbering is not in size order, so Danua_0.stl (the base) sits next to Danua_1.stl (a much smaller piece) and the main body is Danua_23.stl. The two shaft segments (Danua_28.stl and Danua_29.stl) are near-identical and match in size, which is what you'd expect from a column split in two. The Decals/ folder holds eyes_Danua.psd, a layered Photoshop file for printing waterslide eye decals; there is no flat PNG or PDF of it, so you need something that opens PSDs.

3/5 (estimated).

Everything fits a Mars-class plate, and the studio does supply supports and orientations, but only inside the Chitubox project. If you use Chitubox, this drops toward a 2. If you slice anywhere else, you are orienting and supporting 31 raw parts yourself, and a few of them need thought:

  • Danua_23.stl is a large solid part at 84.5 × 80.7 × 116.0 mm, and it will want hollowing with drain holes if you print it from the raw STL. Danua_30.stl is the same story.
  • Danua_0.stl is a 126.2 mm disc only 5.0 mm thick. Flat on the plate it is a suction risk on every layer; tilted, it still fits Mars-class (the plate is 175 mm tall) but needs heavy supports along the low edge.
  • The hair locks (Danua_24.stl, Danua_25.stl, Danua_5.stl, Danua_18.stl) are 11–15 mm thick and 36–45 mm long. They are the parts most likely to warp or snap at support removal.
  • The ornaments are tiny. Danua_26.stl and Danua_27.stl are about 3 × 6 × 8 mm each, and Danua_17.stl is 5.1 mm thick. Print them on a raft with light supports and pull them off with a blade, not your fingers.
  • The horns (Danua_10.stl, Danua_14.stl) taper to points that will need support placement away from the tip.

The only reason this isn't a 4 is that nothing exceeds the plate and the big parts are solid, compact shapes rather than cupped shells. Whether the studio hollowed anything in the Chitubox project I can't see from the STLs; the raw files are solid.

Assembly difficulty

5/5 (estimated).

The count alone puts this at the top of the scale: 31 pieces, and the render is the only guide to where they go. Beyond the count:

  • The seated body (Danua_23.stl) rests on the column slab (Danua_20.stl), which sits on a two-segment shaft (Danua_28.stl, Danua_29.stl) on the base. That is a stacked joint carrying the heaviest part in the kit. I would pin the shaft segments to each other and to the base and let the body sit on the slab with a pin through the hip.
  • The hair mass (Danua_30.stl) is 93.8 mm wide and, judging from the render, hangs out behind the figure with nothing under it. It needs a solid join to the head or back and probably a pin.
  • Four or five separate hair locks join into that mass. Seam lines on hair are easy to hide in the strand direction, but each lock is thin and will want careful dry-fitting.
  • The right arm (Danua_1.stl if I have it right) has to land on the slab at the correct angle for the fingers to sit on the edge.
  • The horns, two hands, two feet and the doll all join on small surfaces.
  • The five ornament parts and the pendant are the fiddly end: two are 3 mm thick. Tweezers and thin CA.

I can't tell from the numbered STLs whether the joins are keyed with pegs and sockets; the report gives sizes only. If they are, the practical difficulty drops a notch, but the count and the stacked column joint keep it at the top of the scale.

Paint difficulty

4/5 (estimated).

Materials count is the main driver. On Danua alone: skin, black hair with highlights, a white dress with a dirt gradient at the hem, a black corset with silver scrollwork, white bandages, a black glove, black sandals, reddish-brown horns, dark metal ornaments, and a red gem. Then the sandstone column and flagstone base, and the doll, which has its own six or seven colors including purple-and-cream stripes on legs a few millimetres across.

What makes it a 4 and not a 5: the eyes ship as a decal file (Decals/eyes_Danua.psd), so there is no freehand iris work, and there are no translucent or glow effects. What keeps it from being a 3: the exposed skin at the face, shoulders, chest and left hand wants proper shading; the dress hem is a soft gradient from white to grey-brown with a red-brown underside that has to look like dirt rather than a mistake; the corset scrollwork is fine raised detail that needs a steady dry-brush or a lining brush; and the doll's stripes and cross are freehand pattern work at a small size.

Paint reference, material by material from the studio's render: hair black with cool grey-blue highlights; skin a pale warm tone with a soft blush at the cheeks; eyes red with a dark pupil (decal); horns a reddish brown, darker at the ridges; horn ornaments dark gunmetal, the crescent the same; ahoge and bangs the same black as the hair. Dress white with warm grey shadow in the folds, hem grading to grey-brown, the turned-up underside a dull red-brown. Corset matte black with silver scrollwork. Pendant a small red gem on a dark cord. Bandages an off-white with grey in the wraps; glove matte black. Sandals black with a pale sole. Column and base a warm sandstone tan, slightly darker in the flutes and between the flagstones. Doll: hair straw blonde with a green cast; hat white with a red band and a red flower; dress red with a pink lower half and a yellow cross on the chest; stockings purple and cream stripes; shoes dark brown or black; face flat pale with simple dark painted eyes.

Moon Figures ships one render for this kit, so the gallery is one image.

Rendered figure of Danua from Granblue Fantasy in a white dress and black corset, seated against a fluted stone column with a small doll at its base on a round flagstone disc.
Three-quarter front view of the full kit against a dark backdrop, with the MoonFigures moon logo in the top left. Danua sits on the edge of the column's top slab with her bandaged right arm resting along it, her left hand on the flagstones at the far left, one black sandal showing under the stained hem of the white dress. The black hair streams out to the right past the column. The doll sits on the tiles at the foot of the column, arms out, facing the camera. The whole round sandstone base is in frame. This is the only view, so it is the reference for every color, the hem staining, the corset scrollwork, the horn ornaments, and the doll's outfit.