BlackRose by NomNom Figures - Kit Overview

A 14-part, 215 mm BlackRose leaning on her greatsword, presupported by the studio for Mars-class plates — the 173 mm sword is the one part that makes the plate height matter.

Share
Full front view of BlackRose standing on a stone base with her greatsword upright beside her.

BlackRose from the .hack series, by NomNom Figures, in their Lootbox line. One size, 14 parts, 215 mm tall on a 104 mm round base, with the greatsword as a single piece that the studio stood upright for the plate.

This post is written from the studio's files and renders. I have not printed it yet.

At a glance

  • Studio: NomNom Figures
  • Character and source: BlackRose, .hack series
  • Section: Anime
  • Versions and sizes (H×W×L): one version only — 215 × 104 × 104 mm, from the studio's scale sheet
  • Parts: 14
  • Presupports: yes, for every part — 14 NOM_*_Supported.stl in Presupports/STL/ and 14 matching .lys in Presupports/Lychee/
  • Largest part and plate fit: raw, sword.stl at 60.2 × 162.5 × 30.5 mm; supported, NOM_sword_Supported.stl at 44.0 × 12.2 × 173.2 mm, stood upright. Everything fits Mars-class (143 × 90 × 175 mm), but 173.2 mm on a 175 mm Z axis is tight.
  • Ratings (estimated): Print 3/5, Assembly 3/5, Paint 4/5 — skill tag advanced
  • Status: files reviewed, not printed
  • Files: NomNom Figures' Patreon and Cults3D store, linked at the bottom.

The model

BlackRose stands upright with her weight on both feet and her hips turned slightly, her right arm reaching up and back over her head to grip the handle of a greatsword that stands point-down on the base behind her. Her left arm hangs loose at her side with the hand open. The sword is taller than she is; its pommel sits above her head and its tip rests on the stone beside her boots. It is a rest pose, not a swing, and the sword carries as much of the composition as she does.

This post uses six of the studio's images for this release: four color full views (Colored_01.png to Colored_04.png), the scale and parts sheet (Scaleparts.jpg), and a gray two-angle turntable sheet (Turntable.JPG). The description below comes from those plus the part list. The renders carry the studio's LOOTBOX mark; no month or year is printed on any of them.

Her hair is white, short and spiky, with a separate bangs piece. Her eyes are red and her skin is a warm tan. Yellow marks sit under each eye like a pair of short strokes, and the same yellow runs in tattoo-like lines across her collarbone, down her sternum and abdomen, along both upper arms, and down her legs. Her top is a two-cup breastplate in deep magenta with gold trim, a gold clasp and a white gem at the center, over a black band. At the waist is a wide belt with magenta hip plates, gold edging with rivets, and a dark gray oval gem at the buckle. A white cloth hangs front and back from the belt. Her leggings are purple with salmon-pink lightning-shaped stripes down the thighs and shins. The boots are gunmetal gray with a low heel and a teal cuff studded with gold rivets. Her left forearm wears a magenta bracer with gold spikes at the elbow, a twisted magenta wrap down the forearm, a gold band and a gray plated wrist guard; her raised right arm has a matching magenta and gold spiked band at the elbow and a gold cuff at the wrist. The hands are bare.

The sword is a single-edged greatsword with a dark navy blade, a stepped notch cut into the back edge near the guard, a long fuller down the flat, and a hollow diamond cutout near the tip with lighter blue edges. The crossguard is gold with a blue inlay stripe; the grip is wrapped in gray-lavender cord; the pommel is a gold cap with a ring. The base is a round cobblestone disc, 104 mm across, with cracked flagstones radiating from a center ring. In Colored_02.png the cracks show a teal-blue fill, so the studio may intend water or a glow in them.

The silhouette is a tall vertical: her body, the raised arm, and the sword blade side by side, with the footprint set entirely by the 104 mm base. Nothing overhangs the disc. From the back (Colored_03.png) the blade covers most of her, so the sword's flat is a display surface in its own right.

Versions and sizes

This is a Lootbox release, so it ships in one size only, already split.

  • Lootbox release
    • H×W×L (mm): 215 × 104 × 104
    • Pieces: 14
    • Presupported: Yes — NOM_*_Supported.stl + one .lys per part

Who it suits: a Mars-class printer with a full 175 mm Z (the sword needs almost all of it as supplied), and a painter comfortable with skin, freehand markings and a striped pattern. On a Saturn-class plate the sword can be laid flatter and the whole kit prints in one or two plates.

About the sizes. Every measurement in this post comes from the sculptor's files or the studio's published size information for the unprinted model. A printed kit can differ slightly: resin shrinks a little as it cures, removing supports and sanding takes off some material, and the assembled height depends on how the parts are fitted. Treat the numbers as a close guide, not an exact guarantee.

What's in the download

Sizes are from the STL report. Raw parts are listed as X × Y × Z with Y as the tall axis; supported parts have Z as the tall axis because the studio re-oriented them for the plate.

Figure

  • head.stl: Head with rear hair
    • Size (mm): 29.1 × 26.6 × 25.5
    • Notes: Square socket on the forehead for the bangs; neck socket
  • bangs.stl: Front hair
    • Size (mm): 22.1 × 26.5 × 13.7
    • Notes: Thin spiky strands; square peg to head
  • torso.stl: Torso with breastplate, neck peg and right upper arm
    • Size (mm): 43.8 × 63.0 × 33.4
    • Notes: Arm ends in a socket at the elbow
  • R_arm.stl: Raised right forearm and hand, gripping the sword handle and pommel
    • Size (mm): 39.8 × 53.0 × 20.6
    • Notes: The handle and pommel are on this part, not the sword; hand and grip are the thinnest section
  • L_arm.stl: Left forearm with bracer, wrap and open hand
    • Size (mm): 19.8 × 42.2 × 16.6
    • Notes: Spikes at the elbow; fingers thin
  • legs.stl: Hips, belt and both legs to the boot tops
    • Size (mm): 40.6 × 69.6 × 34.4
    • Notes: Square peg holes at each hip for the leg armor
  • L_shoe.stl: Left boot
    • Size (mm): 15.9 × 63.6 × 26.3
    • Notes: Socket at the top; heel
  • R_shoe.stl: Right boot
    • Size (mm): 17.8 × 65.0 × 26.3
    • Notes: Socket at the top; heel

Cloth and armor

  • L_leg_armor.stl: Left hip plate
    • Size (mm): 26.2 × 41.2 × 20.1
    • Notes: Thin curved plate; peg to hip
  • R_leg_armor.stl: Right hip plate
    • Size (mm): 21.3 × 42.8 × 27.8
    • Notes: Thin curved plate; peg to hip
  • loinClothFront.stl: Front white cloth panel
    • Size (mm): 20.4 × 40.4 × 13.8
    • Notes: Thin, hanging
  • loinClothBack.stl: Back white cloth panel
    • Size (mm): 28.1 × 38.7 × 21.9
    • Notes: Thin, hanging, folds

Base and scene

  • base.stl: Round cobblestone disc
    • Size (mm): 104.4 × 8.4 × 104.4
    • Notes: Heaviest part in the kit; 8.4 mm thick, one large flat underside; foot and sword-tip locators visible on the parts sheet

Accessories

  • sword.stl: Greatsword blade with crossguard and short grip stub
    • Size (mm): 60.2 × 162.5 × 30.5
    • Notes: Tallest part; hollow diamond cutout near the tip; joins the handle on R_arm.stl at the grip

Raw set: 14 parts.

Presupported set. Presupports/STL/ holds the same 14 parts as NOM_<name>_Supported.stl, and Presupports/Lychee/ holds 14 .lys, one per part. The studio hollowed two of them, base.stl and legs.stl. NOM_head_Supported.stl comes out about the same as the raw head, supports included. In every other supported file the extra is supports, with no hollowing.

Two things worth noting in the folder. NOM_sword_Supported.stl is stood upright at 44.0 × 12.2 × 173.2 mm. And NOM_base_Supported.stl has a bounding box of 104.9 × 58.5 × 103.1 mm for a disc that is 8.4 mm thick when flat, so the studio tilted the base steeply on the plate rather than printing it flat. I haven't opened NOM_base_Supported.lys to see the tilt angle or the support layout. No text or link files ship with the kit.

3/5 (estimated). Everything is presupported with a .lys for each part and every part fits Mars-class, which on its own would be a 2. Three things push it up.

The sword. NOM_sword_Supported.stl is 173.2 mm tall as supplied against a 175 mm Mars-class Z axis. That leaves under 2 mm, so any raft height or plate offset in your own profile could take it over. If it doesn't fit, the raw sword.stl at 60.2 × 162.5 × 30.5 mm can be re-supported at a lean. The blade itself is a long, thin slab with a diamond cutout, which means long support runs and a real chance of a warped tip.

The base. base.stl is a 104 mm disc only 8.4 mm thick, and the underside is one large flat surface. Flat on the plate that is a suction risk on every layer; the studio's tilted orientation avoids that, but a tilted 104 mm disc means a tall support forest and a lot of marks on the cobblestone face. The studio hollowed it, so drain holes matter.

Thin parts. bangs.stl, the two hip plates (L_leg_armor.stl, R_leg_armor.stl), and both cloth panels are thin freestanding pieces. R_arm.stl carries the sword handle and pommel on a small part, and the gold ring on the pommel is the smallest feature in the kit. Only base.stl and legs.stl are hollowed by the studio; the rest print solid, which is fine at these sizes.

Assembly difficulty

3/5 (estimated). Fourteen parts, keyed, with one large hanging piece.

The parts sheet shows square pegs and sockets at the main joins: bangs to forehead, head to neck, hip plates to the belt, boots to the leg stubs, forearms to the elbows. Those are hidden or on hard edges and should not need filling.

The sword is the job. It is a 162.5 mm blade that stands on the base beside her and meets the handle at the top, and the handle is part of R_arm.stl, so the join sits on the wrapped grip between the crossguard and the hand. That join carries the blade's weight in shear unless the tip is anchored to the base first. I would pin the tip into the base and pin the grip join, and test-fit the arm, torso and sword together before gluing any of the three.

The cloth panels hang from the belt and the hip plates sit over them, so there is an order: legs, then cloth, then plates. The two arm joins are small; the elbow on the left arm is under the spiked bracer, which helps. Both feet locate on the base at marked spots.

Paint difficulty

4/5 (estimated). Skin covers most of the model — face, arms, midriff, and the back — and the yellow markings on it are freehand lines that have to be clean at this size. Beyond that there are at least nine materials: skin, white hair, magenta armor, gold trim, black under-band, white cloth, purple leggings with a pink stripe pattern, gray boots with teal cuffs, and a navy blade with gold guard. The leggings' lightning stripes are a second freehand pattern. The face is a stylized anime face with red eyes and the under-eye marks. No translucent or glow effects are required unless you read the base cracks as glowing, which would take it to a 5.

Paint reference. From the colored renders: hair white with cool gray shading; eyes red with a dark pupil; skin warm tan; face marks and body markings pale yellow to gold; breastplate deep magenta with gold trim, a gold clasp and a white gem; band under the breastplate black; belt and hip plates magenta with gold edging and gold rivets, buckle gem dark gray; loincloth panels white; leggings purple with salmon-pink stripes; boots gunmetal gray, cuffs teal with gold rivets; left bracer magenta with gold spikes, forearm wrap magenta, band gold, wrist guard gray; right elbow band magenta with gold spikes, wrist cuff gold; sword blade dark navy with lighter blue on the cutout edges, fuller darker, crossguard gold with a blue inlay stripe, grip gray-lavender wrap, pommel gold; base gray cobblestone with brown-gray grout, teal-blue in the cracks in one render.

Full front view of BlackRose standing on a stone base with her greatsword upright beside her.
Full front view under a TURNTABLE banner, head to base, on black. Whole pose in color: raised arm, hanging arm, the sword standing point-down on the base, purple leggings with pink stripes, gray boots with teal cuffs, and the cobblestone disc. This is the color reference for the full figure and the leggings.
BlackRose from the right side, sword edge-on behind her, teal light in the base cracks.
Full view from her front-right, TURNTABLE banner. The raised arm and the spiked band at the elbow are in profile, the blade is edge-on behind her, and the base's cracks show a teal-blue fill. It is the render that shows the base cracks in color and the sword's thin edge.
Rear view of BlackRose with the wide navy blade of her greatsword covering her back.
Full rear view, TURNTABLE banner. The sword's flat covers most of her back: dark navy blade with the fuller, the stepped notch near the guard, the diamond cutout, and the gold crossguard from behind. The back cloth panel and the backs of the boots are visible below. It is the only color view of the blade's flat and the back cloth.
Left profile of BlackRose with the greatsword's edge running from the base to above her head.
Full left-side profile, TURNTABLE banner. The blade's thin edge runs the full height beside her, the boots' heels and the hip plate profile are clear, and the pommel ring is at the top. It shows how little depth the blade has and how the sword tip meets the base.
Gray dimension sheet for BlackRose showing 215 by 104 by 104 mm and the fourteen parts laid out.
Gray scale and parts sheet, LOOTBOX down the center. Left, the assembled figure with dimension arrows reading H – 215 mm, W – 104 mm, L – 104 mm. Right, the 14 parts laid out: sword handle with hand and forearm, legs, torso, bangs, head, hip plate, back cloth, hip plate, left arm, front cloth, two boots, blade, base, labeled 14 PCS PARTS. It is the only source for the kit's dimensions and split.
Two gray views of BlackRose, front and back, on the round cobblestone base.
Gray two-angle sheet, LOOTBOX TURNTABLE down the left edge: the assembled figure from the front-left and from the rear-right on a pale ground. Without color, the sculpt's surface reads clearly — the hair strands, the pattern relief on the leggings, and the cobble edges on the base. It shows the leggings' stripes are sculpted, not just painted.