Rose, Darkness Dragoon by NomNom Figures - Kit Overview

NomNom Figures' Rose from The Legend of Dragoon in her Darkness Dragoon armor: 233 mm tall, 269 mm across the wings, 18 presupported parts, and a pair of large veined wings that will decide how this print goes.

Share
Rose in dark purple Darkness Dragoon armor with green veined wings, one hand raised open, holding a sword point-down.

Rose from The Legend of Dragoon, in her Darkness Dragoon form, by NomNom Figures. This is the studio's Lootbox release for December 2025 (the month is printed on the beauty shot). What stands out is the wingspan: the figure is 233 mm tall but 269 mm wide, and most of that width is two thin, veined wing membranes that print as single parts.

This post is written from the studio's files and renders. I have not printed it yet. Everything below is what the download contains and what the three renders show, with estimates marked as estimates.

At a glance

  • Studio: NomNom Figures
  • Character and source: Rose, Darkness Dragoon armor with wings and sword — The Legend of Dragoon (PlayStation)
  • Section: Fan art
  • Versions and sizes: one size only. H 233 mm × W 269 mm × L 145 mm, from the studio's scale sheet (Scaleparts.jpg). No scale ratio is stated in the files.
  • Parts: 18 (the scale sheet says "18 PCS"; the STL/ folder has 18 files)
  • Presupports: yes, for every part. Presupports/STL/ holds 18 NOM_*_Supported.stl files and Presupports/Lychee/ holds 18 matching .lys files.
  • Largest part and plate fit: raw, L_wing.stl at 115.6 × 111.7 × 58.1 mm; supported, NOM_sword_Supported.stl at 19.8 × 49.9 × 127.6 mm. All 18 parts fit Mars-class (143 × 90 × 175 mm) in both folders; nothing needs Saturn-class.
  • Ratings (estimated): Print 3/5, Assembly 4/5, Paint 5/5. Skill tag: advanced.
  • Status: files reviewed, not printed.
  • Where to get the files: NomNom Figures' Patreon and Cults3D store, linked at the bottom.

The model

The studio shipped three images for this release: a beauty shot, a scale-and-parts sheet, and a gray two-angle turntable. The description here comes from those three plus the part list, so some of what I say about the back and the underside is inferred from the gray views rather than seen in color.

Rose stands upright on a slab of broken rock, weight on both feet, with the wings spread wide and high behind her. Her right arm hangs at her side in a full armored gauntlet and holds a long, narrow sword point-down; in the turntable front view the tip reaches to about the level of the base's surface, beside the rock rather than on it, though I can't tell whether the tip clears the base or rests against it. Her left arm is raised to shoulder height, palm open and turned outward, fingers spread. The head is level and looks straight ahead.

The identifying details are all Darkness Dragoon: the horned headpiece, the winged shoulder guards, the spine-ribbed breastplate, and the wing membranes. Reading the beauty shot item by item: hair is black, a chin-length bob in front with a long fall down the back (the hair.stl part is 68.6 mm on its long axis), with two dark horn-like points rising from the sides of the head, each with a red tip. A circlet on the forehead carries a cluster of orange-red gems. The breastplate and the whole torso armor are a deep purple-black with a blue-violet iridescent sheen, ridged down the center like a spine, with a single large orange-red gem at the sternum. The pauldrons are the same purple-black with inset red panels carrying a dark vein pattern. The upper arms are bare skin. The right forearm is in a purple-black gauntlet with swept fins at the elbow and wrist; the left arm has a black band on the upper arm and a plain black glove. Hip armor is purple-black with engraved swirls and a small blue emblem plate on the front. Fin-shaped side armor pieces hang at each hip. The greaves and boots are dark segmented armor with orange-red gems on the toes. The sword blade is a dark green-teal metal with slotted cutouts and a fin-shaped guard. A length of dark cloth hangs from the back of the belt behind the legs (visible in the turntable back view).

The wings are the largest surface on the kit and the only bright color. Each membrane is a yellow-green that shifts toward blue-green at the edges, with a raised vein texture across the whole surface, and a leading edge in orange-red with dark ribbing. Each wing meets a curved, ribbed strut at the back through a round hub carrying a sun-like emblem.

The face is pale skin, purple eyes, a small nose, and lightly pink lips, with a calm, closed-mouth expression. The base is a low irregular pile of rock rubble, gray in the renders, about 23 mm tall on the raw mesh. The silhouette is the wings: at 269 mm across, they carry the footprint, and the figure itself is a narrow vertical shape between them.

Versions and sizes

This is a Lootbox release, so it is one size only: no 75 mm, no bust, no unsplit set.

  • Single release (Lootbox, December 2025)
    • H × W × L (mm): 233 × 269 × 145
    • Pieces: 18
    • Presupported (format): Yes, all 18 — NOM_*_Supported.stl plus one .lys per part

Who it suits: someone with a Mars-class printer who is comfortable with thin, freestanding parts and with pinning. The individual parts are all small enough for a small plate; the finished piece is not small, and the wings need somewhere safe to live.

About the sizes. Every measurement in this post comes from the sculptor's files or the studio's published size information for the unprinted model. A printed kit can differ slightly: resin shrinks a little as it cures, removing supports and sanding takes off some material, and the assembled height depends on how the parts are fitted. Treat the numbers as a close guide, not an exact guarantee.

What's in the download

One version, 18 parts. Sizes below are from the raw STL/ folder; the supported files follow after the list.

Figure

  • head.stl: Face and head
    • Size mm (X × Y × Z): 16.2 × 30.8 × 15.4
    • Notes: Small; the whole face is on this part
  • bangs.stl: Front hair with the horned points
    • Size mm (X × Y × Z): 21.5 × 28.9 × 17.5
    • Notes: Thin; the horn tips are fine points
  • hair.stl: Long back hair
    • Size mm (X × Y × Z): 43.1 × 68.6 × 30.4
    • Notes: Hangs down the back
  • torso.stl: Chest armor with pauldrons
    • Size mm (X × Y × Z): 67.1 × 56.6 × 30.5
    • Notes: Hollowed in the studio's presupport
  • legs.stl: Hips, thighs, hip armor
    • Size mm (X × Y × Z): 34.7 × 62.2 × 38.8
    • Notes: Hollowed in the studio's presupport
  • L_arm.stl: Arm
    • Size mm (X × Y × Z): 39.5 × 36.3 × 47.8
    • Notes: From the box shape, this reads as the gauntlet arm
  • R_arm.stl: Arm
    • Size mm (X × Y × Z): 31.4 × 51.3 × 18.2
    • Notes: Flatter and longer; reads as the open-hand arm with spread fingers — thin fingers
  • L_boots.stl: Left greave and boot
    • Size mm (X × Y × Z): 16.3 × 81.5 × 25.5
    • Notes: Tall and narrow
  • R_boots.stl: Right greave and boot
    • Size mm (X × Y × Z): 19.2 × 77.8 × 38.8
    • Notes: Tall and narrow
  • L_sideArmor.stl: Left hip fin
    • Size mm (X × Y × Z): 26.4 × 71.7 × 27.4
    • Notes: Thin plate
  • R_sideArmor.stl: Right hip fin
    • Size mm (X × Y × Z): 25.3 × 71.3 × 29.5
    • Notes: Thin plate
  • L_wing.stl: Left wing membrane with hub
    • Size mm (X × Y × Z): 115.6 × 111.7 × 58.1
    • Notes: Largest raw part; thin membrane, fine feathered edge
  • R_wing.stl: Right wing membrane with hub
    • Size mm (X × Y × Z): 115.6 × 111.0 × 58.1
    • Notes: Same as left, mirrored
  • L_wingJoint.stl: Left curved ribbed strut, back to wing hub
    • Size mm (X × Y × Z): 50.1 × 68.8 × 37.0
    • Notes: Slender; carries the wing's weight
  • R_wingJoint.stl: Right curved ribbed strut
    • Size mm (X × Y × Z): 48.9 × 69.6 × 36.6
    • Notes: Slender; carries the wing's weight
  • Companion: none

Cloth

  • cloth.stl: Belt cloth hanging behind the legs
    • Size mm (X × Y × Z): 57.1 × 57.2 × 39.9
    • Notes: Thin drape; low triangle count for its size

Base and scene

  • base.stl: Rock rubble base
    • Size mm (X × Y × Z): 72.7 × 22.8 × 96.9
    • Notes: Heaviest part; hollowed in the studio's presupport

Accessories

  • sword.stl: Sword, blade and guard
    • Size mm (X × Y × Z): 59.7 × 77.9 × 82.8
    • Notes: Long thin blade; 127.6 mm on its long axis once oriented for supports
  • Alternates: none

No pegs or sockets are legible on the parts sheet at this size, so I haven't confirmed how the wing hubs, wing joints, arms, and neck are keyed.

The studio hollowed three parts in their supported files (base, legs, torso); the other fifteen are the raw part plus supports. Nothing odd in the folder: 18 raw, 18 supported, 18 .lys, no text files, no alternates.

3/5 (estimated).

  • Every part is presupported and every part fits Mars-class flat, which keeps this off 4.
  • The wings are what push it past 2. L_wing.stl and R_wing.stl are 115.6 × 111 × 58 mm each: large, thin membranes with a feathered edge of separate points. On the plate these are the parts most likely to warp, drop a tip, or peel from supports. The vein texture on the face means support marks land on textured surface either way.
  • sword.stl is a thin blade 127.6 mm long in its supported orientation. The wing joints (L_wingJoint.stl, R_wingJoint.stl, ~50 × 69 × 37 mm each) are slender curved struts. Fingers on the open hand and the horn tips on bangs.stl are fine points.
  • base.stl is hollowed by the studio, as are legs.stl and torso.stl. Hollow parts need drain holes; I can't see whether the studio cut them.
  • No large flat or cupped surfaces beyond the wings themselves; the base is a broken rock texture, not a flat slab.

Assembly difficulty

4/5 (estimated).

  • 18 parts, which sits inside the 10–20 band, but two of them are large hanging pieces on slender mounts. Each wing, a large membrane, hangs off a slender wing joint strut. That is a cantilevered load on a thin curved part, and I would plan to pin the wing-to-joint and joint-to-back connections rather than rely on glue. That is what moves this from 3 to 4.
  • The sword hangs from one hand and its tip runs down near the base, so the blade is exposed at two points and the hand join carries its length.
  • The head is separate from the bangs and the hair, so there are three joins around the face and hairline. The neck join and the bangs seam are on smooth, visible surfaces.
  • Both hip fins and the belt cloth attach as separate thin plates.
  • No multi-piece base to align; base.stl is one part.
  • Order matters in a general way: base, legs, boots, torso, then head and hair, then arms and sword, wings last so they don't get in the way of everything else.

Paint difficulty

5/5 (estimated).

  • Realistic face and bare skin on the face, upper arms, and neck; small face part (head.stl is 16 × 31 × 15 mm), so the eyes and lips are tiny.
  • Materials count is high: skin, black hair, purple-black iridescent armor, red vein-patterned pauldron inserts, black leather glove and armband, dark teal metal blade, orange-red gems, gray rock, and the wings.
  • The wings are what earn the 5. The render shows a smooth yellow-green to blue-green shift across a large area, with a translucent look and an orange-red leading edge. That is a large gradient over a textured surface, and if you want the membrane to read as translucent you're into glazes or a clear resin.
  • The armor's blue-violet sheen over purple-black is a second gradient, this time on every plate.
  • The pauldron inserts carry a freehand vein pattern in dark red on red.

Paint reference (studio color scheme from the beauty shot): hair — black, glossy, with red tips on the two horn points. Circlet — dark metal with orange-red gems. Skin — pale, warm. Eyes — violet-purple. Lips — soft pink. Torso, pauldron shells, hip armor, greaves, gauntlet — deep purple-black with a blue-violet iridescent highlight. Pauldron inserts — red with a darker red vein pattern. Chest gem and boot gems — orange-red. Left upper-arm band and glove — matte black. Front hip emblem — blue. Sword — dark green-teal metal. Wings — yellow-green membrane shifting to blue-green at the trailing edge, raised veins in the same tone, leading edge orange-red with dark ribbing; hub emblem in the same purple-black as the armor. Wing struts — dark ribbed metal (only seen in the gray turntable, so the exact color is not on any render). Belt cloth and base — only seen in gray; no colored view of the back exists, so I don't know their colors.

The studio shipped three images for this release.

Rose in dark purple Darkness Dragoon armor with green veined wings, one hand raised open, holding a sword point-down.
Color close-up, front three-quarter, framed from the top of the wings to the knees, with the "LOOTBOX" release mark running up the left edge and "DECEMBER 2025" under the studio logo. Shows the full color scheme: black hair with red-tipped horns, the gem circlet, purple eyes, purple-black iridescent armor with red pauldron inserts, the orange-red chest gem, bare upper arms, the black glove on the raised open hand, the gauntlet on the sword arm, and the yellow-green veined wings with orange-red leading edges. This is the only colored view.
gray scale sheet showing Rose at 233 mm tall and 269 mm wide beside her 18 separate parts.
Two panels. Left: gray full figure on the rock base from the left three-quarter with the dimension arrows, H 233 mm, W 269 mm, L 145 mm, labeled "SCALE". Right: the 18 parts laid out in gray, labeled "18 PCS PARTS": two curved wing struts, gauntlet arm, long hair, bangs, head, cloth, both wings, open-hand arm, torso, sword, legs, both boots, both hip fins, base. This is the only view of the parts separated and the only source for the dimensions.
gray front and back views of the Rose figure with wings spread on a rock base.
Gray two-angle sheet: front view on the left, rear three-quarter on the right, both on the rock base, with "LOOTBOX TURNTABLE" up the left edge. The rear view is the only look at the long back hair, the belt cloth hanging behind the legs, and how the ribbed wing struts run from the back to the wing hubs. The front view shows the sword tip reaching down beside the base.